INSTALLATION INSTRUCTIONS
LAT-NR161
LED Tail Lights for ’60-‘65 Impala/Caprice, ’67 Impala,
‘75-‘76 Caprice, and ’71-’73 Mustang
MAN#650159b
Kit Includes:
Installation:
1. Remove the original bulb connector from the back side of the housing.
2. Remove the light bulb.
3. Remove the tail light lens.
• On the 60-65 Impala, the screws are directly in the lens.
• On the 67 Impala, the nuts securing the tail light assembly must be removed first from
inside the trunk. Once the assembly is removed, the screws on the back of the housing
can be taken out.
• On the 75-76 Caprice, the nuts securing the tail light assembly must be removed first from
inside the trunk. Once the assembly is removed, the screws on the top and bottom sides of
the housing are removed and the metal trim taken off. Last the screws holding the lens are
removed so the lens can come off.
• On the 71-73 Mustang, the lens is snapped into place with tabs around the outside edge.
Carefully pry the lens off using a flat blade screwdriver.
MAN#650159b
8. Secure the back plate with the supplied #6 screw and lock washer.
9. Place the original lens gasket into place and replace the tail light lens. Tighten the screws
down carefully.
MAN#650159b
Cut off the existing light socket as it will not be used. Do not strip the wires. Trim the wires from
LED assembly to appropriate length once mounted, making sure wires are routed cleanly and
securely.
10.Use the supplied moisture resistant pigtail connectors* to attach the wires from the new LED
assembly to the existing vehicle harness. Insert appropriate wire from vehicle harness and
mating LED assembly wire into a connector and crimp following instructions below.
*For the best connection, soldering is recommended. But to simplify installation, the supplied connectors will provide
a fast weather resistant connection.
The correct crimp method for the supplied connectors is:
1.) Insert UNSTRIPPED wires into the connector and ensure they are all they way in by
observing the clear bottom of the connector to see the wires are touching the end.
2.) Use pliers to push the blue cap down flush with the edge of the clear body, completing the
connection. The connection will only be correct if pressed firmly down with pliers.
Attach to metal bolt or screw for
Ground connection with metal
housings
OR
GREEN wire
from LED
assembly
GREEN wire
from LED
assembly
BROWN wire
from LED
assembly
BROWN wire
from LED
assembly
BLACK wire
from LED
assembly
BLACK wire
from LED
assembly
BLACK wire
from LED
assembly
BLACK wire
from LED
assembly
Turn Signal wire
from vehicle
harness
Tail Light wire
from vehicle
harness
Ground wire from
vehicle harness
with plastic housings
LED wires
Brown
Green
Vehicle harness
Brown or Black
Green or Pink
Taillight
Driver’s Turn
Passenger’s Turn
Ground
Green
Yellow, Purple, or Orange
Black, chassis, or body
Black
11.Repeat for the other side.
12.Test the tail lights, brake lights, and turn signals. If the turn signals do not flash you will need
to upgrade your flasher. If you are replacing only the rear turn signals you should be able to
use a heavy duty electronic flasher from your local parts store. If you are replacing both front
and rear or do not have front bulbs you will need a no-load flasher, Dakota Digital part number
LAT-NLF.
SERVICE AND REPAIR
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is available to help you work through any questions or problems you may be
having installing one of our units.
Should you ever need to send the unit back for repairs, please package the product in a good quality box along with plenty of packing material. Ship the product by UPS or insured Parcel
Post. Be sure to include a complete description of the problem, your full name and address (street address preferred), and a telephone number where you can be reached during the day.
An authorization number for products being returned for repair is needed. We will contact you if any repair charges exist. Any returns for warranty work must include a copy of the dated
invoice or bill of sale.
LED LIGHTING LIMITED LIFETIME WARRANTY
DAKOTA DIGITAL (the Company) warrants to the ORIGINAL PURCHASER of this LED Lighting product under normal use and condition, be proven defective in material or
workmanship DURING THE LIFETIME OF THE CAR IN WHICH IT WAS ORIGINALLY INSTALLED, such defect(s) will be repaired or replaced (at the Company’s option) without charge for parts
or labor directly related to repairs of the defect(s).
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of
defects, transportation prepaid, to the factory. This Warranty is valid for the original purchaser only and may not be transferred.
This warranty does not cover damage to vehicle electrical system. This Warranty does not apply to any product or part thereof which in the opinion of the Company has been
damaged through alteration, improper installation, mishandling, misuse, neglect, or accident.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABLITY, SHALL BE
LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABLITY MUST
BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other that
expressed herein in connection with the sale of this product.
FOR SERVICE SEND TO: DAKOTA DIGITAL, 4510 W. 61st ST N., SIOUX FALLS, SD 57107 USA (800) 852-3228
Email us at [email protected]
MAN#650159b
|