User Guide
Motorola® ClutchTM i465
www.nextel.com
© 2009 Sprint. Sprint and the NEXTEL name and logo are trademarks
of Sprint. Other marks are the property of their respective owners.
4/17/09
Class B Digital Device
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
As a personal computer peripheral, this device complies with part 15 of
the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. See 47 CFR Sec. 15.19(3).
This equipment has been tested and found to comply with
Note
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
Responsible Party Name: Motorola, Inc.
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: Motorola Clutch i465
Model Number: H98XAH6JR7AN
FCC-ID: IHDT56KB1
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Ⅲ Reorient or relocate the receiving antenna.
Ⅲ Increase the separation between the equipment and
receiver.
Ⅲ Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Ⅲ Consult the dealer or an experienced radio/TV
technician for help.
FCC Notice to Users
The following statement applies to all products that have received FCC
approval. Applicable products bear the FCC logo, and/or an FCC ID in
the format FCC-ID: IHDT56JQ1 on the product label.
Motorola has not approved any changes or modifications to this device by
the user. Any changes or modifications could void the user’s authority to
operate the equipment. See 47 CFR Sec. 15.21.
Table of Contents
Because of updates in phone software, this
printed guide may not be the most current
version for your phone. Visit www.nextel.com
and sign in to access the most recent version
of the user guide.
User
Guide
Note
Introduction
This User Guide introduces you to your wireless service
and all the features of your new phone.
Please refer to the Important Safety
about information that will help you safely use
your phone. Failure to read and follow the
Important Safety Information in this phone
guide may result in serious bodily injury,
death, or property damage.
WARNING
Throughout this guide, you’ll find tips that highlight
special shortcuts and timely reminders to help you
make the most of your new phone and service. The
Table of Contents and Index will also help you quickly
locate specific information.
You’ll get the most out of your phone if you read each
section. However, if you’d like to get right to a specific
feature, simply locate that section in the Table of
Contents and go directly to that page. Follow the
instructions in that section, and you’ll be ready to use
your phone in no time.
i
Use and Care
To care for your Motorola phone, keep it away from:
liquids of any kind
dust and dirt
Don’t expose your phone to water, rain,
extreme humidity, sweat, or other
moisture.
Don’t expose your phone to dust, dirt,
sand, food, or other inappropriate
materials.
extreme heat or cold
cleaning solutions
Avoid temperatures below -10°C/14°F or
above 45°C/113°F.
To clean your phone, use only a dry soft
cloth. Don’t use alcohol or other
cleaning solutions.
microwaves
the ground
Don’t try to dry your phone in a
microwave oven.
Don’t drop your phone.
ii
3. Press and hold the End/Power key (.) for two
seconds to turn the phone on.
Ⅲ If your phone is activated, it will turn on, search for
service, and enter standby mode.
1. Setting Up Service
Your Phone” on page 2 for more information.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ You may see a prompt to update your browser
information. Press the left softkey (the top left key
below the display screen) to select Ok and complete
the task.
Note
4. Make your first call.
Ⅲ Use your keypad to enter a phone number.
Ⅲ Press ,.
Setting Up Your Phone
Softkeys ( K)
( ;)Navigation key
1. Make sure your SIM card is in place.
Menu Key (
/)
()) Speaker
Talk Key (,)
( .) End/Power Key
(r) OK Key
2. Install the battery.
1
encounter security messages, call Nextel Customer
Service at 1-800-639-6111 from any other phone.
Your phone’s battery should have enough charge for
your phone to turn on and find a signal, set up your
voicemail, and make a call. You should fully charge
your battery as soon as possible. See “Charging the
Note
Setting Up Voicemail
All unanswered calls to your phone are automatically
transferred to your voicemail, even if your phone is in
use or turned off. Therefore, it is recommended that you
set up your voicemail and personal greeting as soon
as your phone is activated.
Activating Your Phone
ⅷ If you purchased your phone at a Nextel Store, it is
probably activated and ready to use.
1. Using your Motorola ClutchTM i465 phone, call your
ⅷ If your phone is not activated, please call Nextel
Customer Service at 1-800-639-6111 from any other
phone.
wireless phone number.
2. Follow the system prompts to:
Ⅲ Create your passcode.
You must be in an area covered by the Nextel
National Network when you first power up your
phone.
Tip
Ⅲ Record your name announcement.
Ⅲ Record your greeting.
ⅷ When you power up your phone the first time, it
performs a series of security checks. For example, it
verifies the phone is Nextel-approved and the correct
SIM card is installed. If you don’t pass the security
checks, your phone displays messages and screen
prompts showing what to do next. If you still
For more information about using your voicemail, (see
2
Account Username and Password
Enabling Security
If you are the account owner, you will create an account
username and password when you sign on to
www.nextel.com. (Click Need to register for access? to get
started.) If you are not the account owner (if someone
else receives the bill for your service), you can get a
sub-account password at www.nextel.com.
You must enable security the first time you power on
your phone or within ten days of first activation of your
phone.
1. Press and hold . for two seconds to power on
your phone.
When you go to www.nextel.com, you will be
redirected to www.sprint.com by default. Follow the
sign in instructions above to access your Nextel
account.
Note
2. Press Ok (right softkey).
3. You are prompted to enable security. Press Yes
(right softkey). A series of screens followed by the
default homepage displays.
Voicemail Password
4. Press . to return to standby mode.
You will create your voicemail password (or passcode)
when you set up your voicemail. See “Setting Up
Voicemail” on page 2 for more information on your
voicemail password.
Account Passwords
With Nextel service, you enjoy unlimited access to your
personal account information and voicemail account.
To ensure that no one else has access to your
information, you need to create passwords to protect
your privacy.
3
From Your Motorola Clutch i465 Phone
ⅷ Press *4, to check minute usage and account
Getting Help
balance.
Managing Your Account
ⅷ Press *3,to make a payment.
Online: www.nextel.com
ⅷ Access your account information.
From Any Other Phone
ⅷ Nextel Customer Service: 1-800-639-6111.
ⅷ Business Customer Service: 1-800-390-9545.
ⅷ Check your minutes used (depending on your
service plan).
ⅷ View and pay your bill.
Operator Services
ⅷ Enroll for online billing and automatic payment.
ⅷ Purchase accessories.
Operator Services provides assistance when you place
collect calls or when you place calls billed to a local
telephone calling card or third party.
ⅷ Shop for the latest phones.
ᮣ
Press
0,.
ⅷ View available service plans and options.
For more information or to see the latest in products
and services, visit us online at www.nextel.com.
4
4. Left Softkey (-) lets you select softkey actions or
menu items corresponding to the bottom left line
on the display screen.
17. Volume
Button
5. Menu Key (/) lets you access the phone’s menu
from standby mode and allows you to access
context-sensitive menus from other screens.
18. Direct
Connect
(DC) Button
6. Talk Key (,) allows you to place or receive calls,
answer Call Waiting, or use Three-Way Calling.
19. Audio Jack
7. Function Key (\) toggles access to symbols and
numbers while using the QWERTY keypad.
20. Micro USB
Connector
8. Keypad lets you enter numbers directly in standby
mode and when adding numbers to contacts.
21. QWERTY
Keyboard
Key Functions
9. Navigation Key scrolls through the phone’s menu
options and acts as a shortcut key from standby
mode.
1. Voicemail LED (7) appears on the display when you
receive new voicemail messages.
10. OK Key (r) selects the highlighted choice when
2. Text Message LED (9) appears on the display when
you receive new text messages.
navigating through a menu.
11. End/Power Key (.) allows you to end calls, return to
3. Bluetooth LED (8) glows solid while the phone is
pairing or is discoverable and blinks while
connected. The LED turns off when no Bluetooth
accessories are connected to the device.
standby mode, or turn the phone on or off.
12. Speaker Key ()) lets you place or receive calls in
speaker mode. In standby mode, pressing the
6
speaker key turns Direct Connect speaker mode
on and off.
21. QWERTY Keyboard lets you easily enter text for
messaging, Web browsing, and entering Contacts and
calender events.
13. Right Softkey (-) lets you select softkey actions
corresponding to the bottom right line on the
display screen.
The use of wireless phones while driving may cause
distraction. Discontinue a call if you can’t concentrate
on driving. Additionally, the use of wireless devices
and their accessories may be prohibited or restricted
in certain areas. Always obey the laws and
Note
14. Camera Key (e) allows you to activate the phone’s
built-in camera.
15. Web Key (L) launches the Web browser.
regulations on the use of these products.
16. Messaging Key ( L) allows you to compose new text
messages.
Getting Started With Your Phone
17. Volume Button allows you to adjust the ringer
volume in standby mode or adjust the voice
volume during a call.
To start using your Motorola Clutch i465 phone:
ⅷ Make sure your SIM card is in place.
ⅷ Charge the battery.
18. Direct Connect (DC) Button allows you to use Nextel
ⅷ Turn on your phone.
19. Audio Jack allows you to connect your headphones
After you’ve completed these items, you are ready to
begin using your new phone.
to phone.
20. Micro USB Connector allows you to connect your
charger or other accessories to your phone.
7
Removing and Inserting the SIM Card
Your SIM Card
To avoid losing information stored in your SIM
card, do not remove it from your phone
unless absolutely necessary.
Important
Locating the SIM Card
Your SIM (Subscriber Identity Module) card is a small
card inserted into the SIM card holder within your
phone behind the battery area.
To remove your SIM card:
1. With your phone powered off, use your thumbs to
press down on the battery door and slide it down
to remove it.
If no SIM card came with your phone, contact Nextel
Customer Service at 1-800-639-6111.
Most users will never need to remove or insert the SIM
card. However, if you wish to, follow the instructions in
2. Push down on the tab and with your fingernail,
carefully slide the SIM card out from under the
edge.
The SIM card is designed for optimal
Contacts storage and feature use. For Nextel
SIM card compatibility information, visit
Important
In some cases, Contacts and Groups may not
be accessible if you move your SIM card to
another phone. Contacts and Groups created
with your Motorola Clutch i465 phone may
not be readable by an older iDEN SIM-based
phone.
8
Battery and Charger
Protect your SIM card as you would any delicate
object. Store it carefully.
Note
Use only Nextel-approved or Motorola-
WARNING
approved batteries and chargers with your
phone. The failure to use a Nextel-approved or
Motorola-approved battery and charger may
increase the risk that your phone will overheat,
catch fire, or explode, resulting in serious
bodily injury, death, or property damage.
To insert your SIM card:
1. With your phone powered off, use your thumbs to
press down on the battery door and slide it down
to remove it.
2. Carefully slide the SIM card into your phone, until it
lies flat in the SIM card holder.
For information on battery safety, see “Battery
Important
Do not touch the gold-colored areas of your
SIM card.
Important
Nextel-approved and Motorola -approved batteries and
accessories can be found at Sprint Stores or through
Motorola. You may order online at www.nextel.com or by
calling 1-866-866-7509.
Your phone’s Lithium Ion (Li-Ion) battery allows you to
recharge it before it is fully drained.
When the battery reaches 5% of its capacity, your
phone makes a sound and displays a message. When
there are approximately two minutes of talk time left, the
phone sounds an audible alert and then turns off.
9
2. Remove the battery cover from the back of the
Long backlight settings, searching for service, vibrate
mode, browser use, and other variables may reduce
the battery’s talk and standby times.
Note
Tip
phone
3. Insert the battery into the opening, making sure the
connectors align. Gently press down to secure the
battery.
Watch your phone’s battery level indicator and
charge the battery before it runs out of power.
Installing the Battery
1. Pull out the connector cover and with your thumbs,
press down on the battery cover on the back of
your phone and slide it down to release it.
4. Replace the battery cover and gently press and
slide it up until it clicks into place.
10
Removing the Battery
1. Make sure the power is off so that you don’t lose
any stored numbers or messages.
2. Remove the battery cover and use your thumbnail
in the slot on the upper left side to remove the
battery from the phone.
Do not handle a damaged or leaking Li-Ion
battery as you can be burned.
WARNING
Charging the Battery
With the approved Li-Ion battery, you can recharge the
battery before it becomes completely run down.
Charge your battery as soon as possible so you can
begin using your phone.
Turning Your Phone On and Off
Always use a Nextel-approved or Motorola-approved
desktop charger, travel charger, or vehicle power
adapter to charge your battery.
Turning Your Phone On
ᮣ
Press and hold .for approximately two seconds.
Using the Phone Charger
As your phone connects to the network, you see a
connecting message. Your phone may require you to
enter identifying information to use it or to access
specific features.
ᮣ
Plug the flat end of the charger into the phone’s
micro USB connector and the other end into an
electrical outlet.
11
Turning Your Phone Off
Phone In Use — Your phone is active on a
phone call.
$
0
t
4
ᮣ
Press and hold . for two seconds until you see
the powering down animation on the display
screen.
Direct Connect In Use — Your phone is active
on a Direct Connect call.
Your screen remains blank while your phone is off
(unless the battery is charging).
Group In Use — Your phone is active on a
Group Connect call.
Viewing Status Information
Direct Talk — Your phone is off network and
set to Direct Talk mode.
Your phone’s display screen provides information
about your phone’s status and options. This list
identifies the symbols you’ll see on your phone’s
display screen:
Talkgroup In Use — Your phone is active on a
Talkgroup call.
r
c
Bluetooth In Use — Your phone is using
Bluetooth. If this icon is blinking, your phone
is in discoverable mode. If this icon is static,
a Bluetooth connection is active.
Battery Strength — A fuller battery indicates a
greater charge. The “plug” icon (bottom
rows) indicates the phone is charging.
d e
f g
y x
w h
$(
Active Phone Line — 1 indicates phone line 1
is ready to make calls; 2 indicates phone
line 2 is ready to make calls.
Signal Strength — More bars next to the
antenna indicate a stronger signal.
z {
|}
Call Forward — Your phone is set to forward
"#!
%&'
No Service — Your phone is without service.
You cannot make or receive any type of call.
~
12
Ringer Off — Your phone is set to not ring.
TTY — You are ready to use your phone to
make calls using a teletypewriter device.
/5
A B
W
Speaker Off — Direct Connect sound is set to
come through the earpiece rather than
through the speaker.
"
Hearing Aid — Your phone is set for use with a
hearing aid and is active on a phone call.
Messages — You have one or more
messages. See “Message Center” on
2 6
1 3
5
:
Voice Record — You have one or more voice
records stored. See “Voice Records” on
Text Input — You are using one of the phone’s
text entry methods. See “Selecting a Text
QRS
TUV
WX
Navigating Through Menus and
Options
Internet — You are ready to browse the
Internet or are browsing the Internet using a
secure connection. See “5. Data Services”
7 >
?
ᮣ
Press /to access the main menu, and then use
the navigation key to scroll through menu items.
Transmitters — Your phone is set not to
receive calls and other transmissions. See
L
To navigate through a list-type menu, simply press your
navigation key up or down. The scroll bar at the right of
the menu keeps track of your position in the menu at
all times.
13
Many features provide context-sensitive menus that let
you access related features and actions. This icon f
appears any time a context-sensitive menu is available.
Press /to access the menu.
Backing Up Within a Menu
To go to the previous menu:
ᮣ
Press Back (right softkey).
To return to standby mode:
Press ..
Selecting Menu Items
ᮣ
As you navigate through the menu, menu options are
highlighted. Select an item by highlighting it and
pressing r.
Shortcuts and Personalized Keys
In standby mode, your phone gives you ways to quickly
access features you use frequently:
For example, to view your text messages:
1. Press /to access the main menu.
most menu options by pressing a number on your
keypad or saying the voice name of the shortcut.
2. Select Messages by highlighting Messages and
pressing r.
menu items to the navigation keys, softkeys and r,
reorder the main menu, add Java applications to the
main menu list, and set a main menu item to appear
when you turn on your phone.
3. Select Inbox by highlighting it and pressing r.
(If you have any MMS messages, they are
displayed.)
For the purposes of this guide, the above steps
Note
condense into “Press /> Messages > Inbox.”
14
composing MMS messages and entering Contacts
information.
Help
Your phone contains an in-device help program to
help you understand complicated or seldom used
features. When you access a feature, Help sometimes
appears as a menu item or softkey. Select Help and
read the text for a quick overview of the feature. For
more information, refer to this guide.
To choose a text input mode:
1. At a screen requiring you to enter text, press /to
change the text input mode.
2. Select one of the following options:
Ⅲ Alpha to enter text directly using the keyboard.
Displaying Your Numbers
Ⅲ Word to enter text using a predictive text system
that reduces the number of key presses required
My Info lets you view your phone number, Direct
Connect number, and other phone information.
Ⅲ Text Settings allows you to change the settings for
ᮣ
Press /> My Info.
You may need to select More to display My Info.
Ⅲ Insert to insert Quick Notes preset messages
(Insert QNotes) or additional multimedia elements
such as pictures or audio files into a message.
(See page 53.) (You can also access Quick Notes
by pressing QNotes [left softkey] when beginning
a message.)
Note
Entering Text
Selecting a Text Input Mode
When entering text, press the C key to change
letter capitalization (ABC > Abc > abc).
Tip
Your phone’s full QWERTY keyboard makes it easy to
enter text whenever you need to, for example when
15
the database. Repeat until the desired word
appears.
Entering Text Using Word Text Input
Word text input (iTAP) reduces the number of
keystrokes needed to enter a word by predicting
complete words as you type. While you enter letters,
Word mode matches your keystrokes to words in its
database and displays the most commonly used
matching word. You can add your own words to this
database.
Adding a Word to the Database
If a specific word is not displayed as an option when
you are using Word, add it to the database.
To use Word text input, you must turn the Complete
Word setting on. From a text entry screen, press />
Text Settings > Compl. Word and select On. Press
Back (right softkey) to return to the text entry screen.
Note
3. Select the Word text input mode.
The word will appear as an option the next time you
scroll through options during Word.
1. Select the Word text input mode.
2. Begin entering a word using the keyboard. (For
example, to enter the word “nutrient,” press
N U T.) (If you make a mistake, press Dto erase
a single character. Press and hold Dto erase an
entire entry.)
To change the text input settings:
1. On a text entry screen, press /.
2. Select Text Settings.
3. Select your Primary Input and Secondary Input
language, and whether you want Complete Word
and Next Word features to be on or off.
3. To accept a word and insert a space, press I.
4. If the word that appears is not the desired word,
press the navigation key up or down to change the
word on the display to the next most likely word in
16
Entering Text Using Alpha Mode
You can also enter symbols by pressing B and
scrolling through a grid of symbols. Press Back (right
softkey) to return to entry mode.
Note
To enter Quick Notes:
2. Press the corresponding keys once per letter to
enter a word. (For example, to enter the word “Bill,”
press F G H H). (If you make a mistake, press
Dto erase a single character. Press and hold Dto
erase an entire entry.)
1. From a text entry screen, press QNotes (left softkey).
2. Select a message and press r.
To add a quick note after you have already started
entering a message, press /> Insert >
Add QNotes, and select a message.
Tip
By default, the first letter of an entry is capitalized and
the following letters are lower cased.
Quick Notes preset messages make composing text
messages easier by allowing you to enter quick
messages, such as “Meet me at,” “Let’s get lunch,” or
a customized message of your own.
Note
Entering Symbols, Numbers, and Quick
Notes
To enter symbols or numbers:
Special Function Keys
ᮣ
Press A and then press the corresponding key to
enter a single number or symbol. To enter multiple
numbers or symbols, press and hold A and enter
symbols or numbers. (To return to text entry, press
Aagain.)
Some of the phone’s keys assume different functions
while in Alpha or Word mode.
Spaces
Press I for a space.
17
Capitalization
Accessories
Press C to capitalize letters. Press and hold C to turn
on caps lock.
Your phone comes with the following accessories:
ⅷ A Li-Ion battery and charger.
ⅷ A128K SIM card.
These icons appear:
or
or
Shift is on.
R
S
U
V
Various accessories are available for use with your
MotorolaClutch i465 phone, including cases, vehicle
power chargers, data cables, hands-free accessories,
and more.
Caps lock is on.
When none of these icons appear, letters typed are
lowercase. Scrolling up or down after typing a letter in
Alpha mode changes the letter to the key’s alternate
character (symbol or number).
To order additional accessories, go to www.nextel.com
or call1-866-866-7509.You can also contact your
Nextel Authorized Representative or stop by any Sprint
Store. For information on Sprint Store locations, go to
Your phone automatically makes the first letter of a
sentence uppercase.
Punctuation
Using a Remote Direct Connect Button
Press A to insert punctuation and B to view a grid of
available symbols. Press rto select a symbol.
If you are using a headset or other optional accessory
with a remote Direct Connect button, you can use the
remote Direct Connect button for phone calls, Direct
Connect calls, and Group Connect calls.
Additional punctuation symbols are available in
Symbols mode.
Note
For phone calls, use the remote Direct Connect button
to answer calls, switch between calls, and end calls.
18
Hold the remote Direct Connect button for less than
two seconds to answer calls and switch between calls.
Hold the remote Direct Connect button for more than
two seconds to end calls.
For Direct Connect calls and Group Connect calls, use
the remote Direct Connect button as you would the
Direct Connect button on your phone.
When using a headset, the Direct Connect button on
your phone works the same way as when you are not
using a headset. Direct Connect and Group Connect
sounds will be heard through the headset.
19
ⅷ Digital Wireless Phone Calls offer clear calls and other
services, such as missed call notification, Three-Way
3. Making and Answering
Calls
ⅷ Direct Connect Calls allow two-way radio
communication with other Nextel Direct Connect
users within the Nextel National Network (page 27).
ⅷ Group Connect Calls allow coast-to-coast two-way
radio calling to up to 20 Nextel Direct Connect
customers simultaneously (page 29).
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ⅷ Nextel Direct Send allows you to send contact information
in Direct Connect and Group Connect calls and send
pictures in Direct Connect calls (page 33).
ⅷ Talkgroup Calls allow two-way radio calling to up to
100 Nextel Talkgroup customers simultaneously
To learn more about the differences between Nextel
Group Connect calls and Talkgroup calls, please see
Note
Types of Calls
With the Nextel National Network, Nextel Direct
Connect, and your MotorolaClutch i465 phone, you
have the following traditional wireless phone and
Nextel Direct Connect services available to you:
ⅷ Nextel Direct Talk allows for two-way radio
communication “off the network” between two or
more phones equipped with this capability
20
Answering Calls
Phone Calls
1. Make sure your phone is on.
Making Calls
When your phone is off, calls go directly to voicemail.
Note
Placing a traditional wireless phone call from your
MotorolaClutch i465 is as easy as making a call from
any landline phone.
2. Press , to answer an incoming call.
Your phone notifies you of incoming calls by any
combination of ringing or vibrating, the indicator light
flashing, the backlight illuminating, or the screen
displaying an incoming call message.
1. Make sure your phone is on.
2. Enter a phone number from standby mode and
press ,. (If you make a mistake while dialing,
press Delete [right softkey] or Dto erase the
numbers.)
If the incoming call is from a number stored in your
Contacts, the entry’s name is displayed. The caller’s
phone number may also be displayed, if available.
3. Press . when you are finished.
Ending a Call
To redial your last outgoing call, press and hold ,.
Tip
ᮣ
To end a call, press ..
You can also place calls from your phone by using
Missed Phone Calls
Missed phone calls are forwarded to voicemail. When
you do not answer an incoming call, you will see a
Missed Call notification.
21
To display a Missed Call entry from the notification screen:
feature. Because of the limitations of this feature, always
provide your best knowledge of your location to the
emergency response center when you make an
emergency call.
ᮣ
Press View (left softkey). (To dial the phone number,
press , after displaying the entry.)
To display a Missed Call entry from standby mode:
1. Press /> Recent Calls.
2. Select an entry and press r.
Emergency Calls
Your phone supports emergency calling. Emergency
phone calls can be made even when your SIM card is
blocked or not in your phone.
ᮣ
Dial 911and press , to be connected to an
emergency response center. If you are on an active
call, you must end it before calling 911.
When you make an emergency call, your phone’s GPS
Enabled feature can help emergency service
personnel find you, if you are in a location where your
phone's GPS antenna has established a clear view of
the open sky and your local emergency response
center has the equipment to process location
22
In-Call Options
Always report your location to the 911 operator
when placing an emergency call. Some
designated emergency call takers, known as
Public Safety Answering Points (PSAPs) may not
be equipped to receive GPS location information
from your phone.
Important
Press /during a call to display a list of available
in-call features. To select an option, highlight it and
press r. The following options may be available:
ⅷ Hold to place the call on hold.
Emergency calls cannot be placed while the
keypad is locked.
ⅷ 3 Way to initiate a three-way call.
ⅷ Use Bluetooth to switch from the phone’s microphone
to a Bluetooth device.
If you have not registered on the network,
emergency calls cannot be placed while your
SIM card is in your phone.
ⅷ 2nd Call to place a second call.
ⅷ Contacts to display your Contacts list.
ⅷ Recent Calls to display Recent Calls list.
ⅷ My Info to display your phone’s Information.
ⅷ Memo to display the phone’s electronic notepad.
ⅷ Datebook to enter a datebook event.
ⅷ Messages to create a message.
If you are bringing your phone number to Nextel
from your previous carrier, you may receive a
temporary telephone number while your Nextel
phone is being programmed with your
permanent phone number. If you make a call to
911 and the call fails, the 911 emergency
response center will not be able to call you back
on your Nextel phone if in the meantime, your
Nextel phone has been programmed with your
permanent telephone number. If the call is
disconnected before location and details have
been provided, call 911 again and advise that you
were disconnected.
ⅷ Store to store a new contact.
ⅷ Record to record the phone call.
ⅷ GPS to enter the GPS application.
ⅷ In Call Setup to modify the in-call features.
23
2. Press rto view the Call Details.
Speakerphone
3. Press ragain to view the Call Info.
ᮣ
Press )during a call to route the phone’s audio
through the speaker or the earpiece.
Saving a Phone Number
Because of higher volume levels, do not
place the phone near your ear during
speakerphone use.
WARNING
1. Enter a phone number and press /.
2. Highlight Store Number and press r.
3. To store a new entry, highlight [New Contact] and
Mute
press rto add a new entry.
ᮣ
Press Mute (left softkey) during a call to mute the
microphone. Press Unmute (left softkey) to unmute
the microphone.
– or –
Search for an existing contact name and press r
to save the new number.
End-of-Call Options
4. Enter or edit information as necessary and press
Save (left softkey) to save the Contact.
After you receive or make a call, the call duration is
briefly displayed. You are then automatically taken to
the Recent Calls list.
For more information about Contacts, see
To save a number that is not in your contacts:
Finding a Number
ᮣ
Highlight an entry and press Save (left softkey).
To find Contacts entries, you can either scroll through
the list using your navigation key or you can search
Contacts entries by name.
To view Call Details and Call Info:
1. Select a recent call.
1. Press /> Contacts.
24
2. Press Search (left softkey).
the letter P more than once. Each P represents a
three-second pause.
3. Enter the first few letters of a Contact's name and
press r. (The first contact entry that matches the
entered text will be highlighted.)
– or –
Press the letter W on the keyboard. The W means
your phone waits before dialing further. A message
appears asking about sending the rest of the
digits.
4. To display the Contacts entry, press r. To dial the
entry's default phone number, press ,.
Phone Numbers With Pauses
3. Enter additional numbers.
You can dial or save phone numbers with pauses for
use with automated systems, such as voicemail,
conference call, or credit card billing numbers.
4. Press , to dial the number.
– or –
Press /> Store Number to save the number in
your Contacts.
There are two types of pauses available on your phone:
ⅷ Wait sends the next set of numbers when prompted.
When dialing a number with a wait, press Yes (left
softkey) to send the next set of numbers.
Note
ⅷ Pause automatically sends the next set of numbers
after three seconds.
You can have multiple pauses in a phone number
and combine waits and pauses.
Note
To dial or save phone numbers with pauses:
1. Enter the phone number.
2. Press the letter P on the keyboard. The P represents
a three-second pause. For a longer pause, press
25
2. Say a voice name. Your phone plays the name
Making a Call From Contacts
back to you.
1. Press /> Contacts.
3. The call is placed automatically.
2. Highlight an entry and press , to dial the default
phone number.
To stop a phone call from being completed,
press ..
Tip
– or –
Speed Dialing
To dial another number from the entry, highlight
the name, press the navigation key right or left until
the correct number type appears, and then
press ,.
Each phone number stored in Contacts is assigned a
Speed Dial number, which you can use to call that
number. You can store up to 600 numbers in your
phone’s speed dial memory.
Making a Call From Recent Calls
1. Enter a speed dial number and then press #.
2. Press , to dial the number.
To use Turbo Dial® for speed dial locations 1–9:
1. Press /> Recent Calls.
2. Highlight an entry and press ,.
Making a Phone Call Using a Voice Name
ᮣ
Press and hold the appropriate key for
approximately two seconds. The display confirms
that the number has been dialed when it shows
“Calling...”.
If you have created a voice name in Contacts (see
page 99), say the voice name into your phone to enter
the number.
1. Press and hold
s
until a prompt appears telling
Redialing the Last Number
you to say the voice name.
ᮣ
Press and hold ,.
26
Making Direct Connect Calls
Nextel Direct Connect
Nextel offers the following Nextel Direct Connect®
services:
2. Press and hold the Direct Connect (DC) button on
the left side of your phone. Begin talking after your
phone emits a chirping sound.
ⅷ Nationwide Direct Connect allows coast-to-coast Direct
Connect calling to Nextel subscribers to and from
anywhere on the Nextel National Network (U.S.).
3. Release the DC button to listen.
ⅷ International Direct Connect allows Direct Connect
calling to and from select countries.
A Direct Connect call ends automatically after there is
no activity on the call for several seconds.
ⅷ Group Connect® allows nationwide Direct Connect
calling to up to 20 Nextel subscribers simultaneously.
Dialing Direct Connect Numbers
ⅷ TalkgroupSM allows Direct Connect calling to up to 100
Nextel subscribers in the same Direct Connect
ⅷ Nextel Direct TalkSM lets you establish off-network,
two-way radio communication between two or more
Nextel Direct Talk-capable phones. (See “Direct Talk”
Every Direct Connect number has three parts:
ⅷ An area ID.
ⅷ A network ID.
ⅷ A member ID.
An asterisk separates each part (for example:
999*999*9999). When you enter a number containing
all three parts, you must separate them with asterisks.
See www.nextel.com for more details on these Direct
Connect services. Pricing for each of these services is
based on your service contract.
27
Making Direct Connect Calls From Contacts or
Recent Calls
The number of digits in each part of a Direct
Connect number may vary. For example, your Direct
Connect number may be formatted as
999*999*9999, while another valid number may
appear as 555*555555*55.
Note
make calls.
If you are calling or saving a Direct Connect number
for a Sprint phone with Direct Connect capabilities,
the Direct Connect number may be the same as the
wireless phone number. When dialing or saving the
Direct Connect number, insert asterisks in place of
hyphens (913*555*1234).
1. Press /> Contacts or Recent Calls.
2. Highlight an entry and then press and hold the DC
button to call the entry’s Direct Connect number.
You can make Direct Connect calls while viewing
entry details on either list. Display the entry details or
My Info from another phone (in Recent Calls) and
press and hold the DC button.
Tip
When you store a Direct Connect number in
Contacts, be sure to include the entire number,
including the asterisks.
Tip
Making Direct Connect Calls Using a Voice Name
Using Just the Member ID
If you have created a voice name in Contacts, say the
voice name into your phone to enter the number.
If you are contacting someone sharing your network
and area IDs, you only need to enter the member ID
(the last part of the number).
1. Press and hold the Speaker key (s) until a prompt
appears telling you to say the voice name.
1. Enter a member ID.
2. Say a voice name. Your phone plays the name
back to you.
2. Press and hold the DC button.
3. Press and hold the DC button.
28
Answering Direct Connect Calls
In order to store Groups to your MotorolaClutch i465
phone, you must use the 128K SIM card that came
with your phone. The 128K SIM card is labeled
“Nextel 600 Contcs & 25 Grps”. With this SIM card, a
maximum of 25 groups can be added to your
MotorolaClutchi465 phone. Group entries created
with your MotorolaClutch i465 phone may not be
readable by older iDEN SIM-based phones.
Note
When you receive a Direct Connect call, your phone
emits a tone or vibrates. You then hear the voice of
your caller.
1. Wait for the caller to finish speaking.
2. Press and hold the DC button. Continue as you
would on any Direct Connect call.
Making Group Connect Calls
3. Press . to end the call.
1. From Contacts or the Recent Calls list, highlight or
select a Group.
A Direct Connect call ends automatically after there is
no activity on the call for several seconds.
2. Press the DC button.
You can also start a Group Connect call by entering
Group Connect Calls
Tip
or selecting a Direct Connect number. See “Starting
A Group Connect call is similar to a Direct Connect call
to one user, but is made to multiple Direct Connect
subscribers at once. You can create Groups from your
phone and call up to 20 other Group Connect-
compatible phones* anywhere on the Nextel National
Network. You can create a Group for one-time use or
store it to Contacts so you can call it at any time.
Answering Group Connect Calls
ᮣ
Proceed as if answering a Direct Connect call from
one user. Only one person at a time may speak on
a Group Connect call.
* Not all phones are Group Connect-compatible. See
29
the Direct Connect number from your keypad. You can
also add all members in an existing Group to another
Group by selecting the Group name from Contacts.
Creating Groups in Contacts
1. Press /> Contacts.
2. Select [New Group].
To add Group members from Contacts, the Recent Calls
list, or Memo:
3. To assign a name to the Group, enter the name.
1. While creating a Group, select [Add Member].
If you do not assign a name, the Group is named
“Group” followed by the number of members in the
Group. For example, “Group (8)” is a group with eight
members.
Note
To move between Contacts, the Recent Calls list, and
Memo, scroll left or right.
Note
2. Highlight desired entries and press r. A
checkmark appears next to each selected
member.
5. To create a voice name for the Group (optional),
select [Options] > Voice Name. Follow the prompt to
record a Group name. When you have finished,
press Back (right softkey).
To deselect a member, highlight it and press r.
Note
3. Press Done (left softkey) and then press Save (left
softkey) to save the group.
6. Press Save (left softkey).
To add Group members manually from the keypad:
1. While creating a Group, select [Add Number].
2. Enter the Direct Connect number.
Adding Group Members
You can add Group members that have a Direct
Connect number and Group Connect-compatible
phone to your Group by selecting them from Contacts,
the Recent Calls list, Memo, or by manually entering
3. Press rand then press Save (left softkey).
30
Starting a Group Connect Call With a
Direct Connect Number
Removing Members or Groups
To remove a member from a Group:
1. Press /> Direct Connect, select entries for a Group
Connect call, and go to step four. (To add
members or numbers from Recent Calls or Memo,
scroll left or right.)
1. From Contacts, highlight a Group and press Edit
(left softkey).
2. Highlight a member and press />
Remove Member.
– or –
3. Press Save (left softkey).
From standby mode, enter a Direct Connect
number.
You can also select Remove All however, you will
have to add at least two new members to save the
edited Group.
Note
– or –
From Contacts or Recent Calls, highlight an entry
containing a Direct Connect number.
To delete a Group from Contacts:
1. From Contacts, highlight a Group.
2. Press /> Delete Group.
2. Press /> New Group or Call New Group.
3. Press Yes (left softkey).
4. To save the Group, press /> Store Group.
– or –
Storing Groups
To store a group to Contacts from the Recent Calls list:
To call without saving, press Done (left softkey).
1. From the Recent Calls list, select a Group and
press Save (left softkey).
5. To make the call, press the DC button.
31
2. Add more information to the entry (optional).
3. Press Save (left softkey).
To store a member from an active call:
1. During an active Group Connect call, press />
Store Number.
To store a group to Contacts from an active call:
2. Select a number or member to store.
1. During an active Group Connect call, press />
Store Group.
3. Add more information to the entry (optional).
2. Add more information to the entry (optional).
You cannot record a voice name during an active
call.
Note
You cannot record a voice name during an active
call.
Note
4. Press Save (left softkey).
3. Press Save (left softkey).
Group Connect Call Information
Storing Members of Groups
While you are in a Group Connect call, the following
appears on the screen:
To store a member from the Recent Calls list or within
Contacts:
ⅷ The name of the Group.
ⅷ The name or the Direct Connect number of the
person speaking.
1. Display a Group and press /> Store Number.
2. Select a number or member to store.
3. Add more information to the entry (optional).
4. Press Save (left softkey).
ⅷ The number of members who are participating in the
Group Connect call.
32
Group Connect Call Details
Nextel Direct Send
During a Group Connect call, you can view details
about the other group members, such as their name or
Direct Connect number, and their status on the call.
Nextel Direct Send lets you use Direct Connect calls to
exchange pictures, My Info, contact information, and
Groups with other phones that have this capability.
To view Group Connect call details:
Nextel Direct Send cannot be used during Talkgroup
calls. Pictures cannot be sent in Group Connect calls.
ᮣ
Press Details (left softkey).
In the Details view, these icons appear next to member
names or Direct Connect numbers:
Sending a Picture
When you send a picture using Nextel Direct Send, the
picture appears on the display of the receiving phone,
and is saved by that phone.
The member of the Group who is
speaking.
F
E
A member of the Group who is active on
the Group Connect call, but not speaking.
Sending a Picture During a Call
You can send a picture at any time during a Direct
Connect call, whether you made or received the call.
(Additional charges may apply.)
A member of the Group who has exited
the call.
D
H
A member of the Group who could not be
reached on the Group Connect call.
You cannot talk or listen on a Direct Connect call while
a picture is being transmitted. Other activities, such as
searching for a picture, do not prevent you from talking
or listening.
A member of the Group whose status is
unknown.
G
33
To send a picture during a call:
When a person sends you My Info from his or her
phone, including his or her Direct Connect number
and IP address, you can then easily store this
information to Contacts from the Recent Calls list
Tip
1. While in a Direct Connect call, press Picture (right
softkey). A list of pictures that can be included in a
Direct Connect call appears.
To start a call by sending a picture:
2. Select a picture and press the DC button to send it.
1. Press /> Media Center and then highlight or
3. Wait while the picture is transmitted. The Direct
Connect call is temporarily interrupted while a
picture is transmitted.
select a picture.
2. Press /> Send Via... > Send via PTT.
4. When prompted, press the DC button to resume
the Direct Connect call.
3. Select A Contact or A Recent Call. These names have
Direct Connect numbers and IP addresses stored.
The first time you send a stored picture after turning
the phone on, the message Picture Fees May Apply
appears and you are prompted to respond. Press
Yes (left softkey) to send the picture. Press No (right
softkey) to cancel.
4. Select a name and press the DC button to send
Note
the picture.
5. When prompted, press the DC button to resume
the Direct Connect call.
Receiving a Picture
Starting a Call by Sending a Picture
When someone sends you a picture using Nextel
Direct Send, your phone emits a tone or vibrates and a
message appears on the display asking you to accept
the picture.
You can start a call by choosing a stored picture from
the Media Center.
To do this, you must have the recipient’s Direct Connect
number and IP address stored in your Contacts.
34
Pictures you receive are saved to your phone’s memory
and are accessible through the Media Center.
To stop the transmission before it is finished, press
Cancel (right softkey).
Tip
When you receive a picture, it appears every time you
are in a Direct Connect call with the person who sent it
unless you delete the picture from the Media Center.
This occurs for the last 20 people who sent you
pictures.
Setting Picture Capability
To turn your phone’s ability to send and receive pictures in
Direct Connect calls on or off:
1. Press /> Settings > DC/GC Options > On/Off Settings.
To accept a picture:
2. Select Pictures and press rto check or uncheck
the box.
1. When you see the message asking you to accept
the picture, press Yes (left softkey). (To decline the
picture press No [right softkey].)
3. Press Done (left softkey) to save the setting.
This setting does not affect your phone’s ability to send
and receive My Info or contact information.
2. Wait while the picture is transmitted. The Direct
Connect call is temporarily interrupted while a
picture is transmitted.
Sending My Info and Contact Information
3. When prompted, press the DC button to resume
When you send My Info or contact information using
Nextel Direct Send, the information you send appears
on the display of the receiving phone. After the call, the
information appears on that phone’s Recent Calls list.
the Direct Connect call.
The first time you accept a stored picture after
turning the phone on, the message Messaging
Fees May Apply appears and you are prompted to
respond. Press Yes (left softkey) to accept the
picture. Press No (right softkey) to cancel.
Note
35
4. When you are finished, press Done (left softkey).
To control whether your information is sent automatically:
1. Press /> My Info.
Sending My Info
You can control what portion of the information in My
Info is sent and whether it is sent automatically in every
Direct Connect call or only when you choose to send it.
2. Press /> Direct Send Setup > Auto Send.
When you send My Info, certain information, such as
your email address or fax number, cannot be
included. To send complete contact information,
create an entry for yourself in Contacts and send it.
Tip
3. Select On to send your information automatically,
or Off to send your information only when you
choose to send it.
When you receive your phone, it is set to send your
information automatically.
Note
The information your phone sends always includes My
Name and Direct Connect.
It may include Line 1, Line 2, Carrier IP, and Private ID2
depending on the options provided by your service
provider and how you set your sending options.
To send My Info during a call:
1. While in a Direct Connect call, press />
Direct Send My Info.
The default setting is Line 1 only.
To change which fields are sent:
1. Press /> My Info.
2. When Ready To Send appears, press the DC button
to send the information.
To start a call by sending My Info:
1. Press /> My Info.
2. Press /> Direct Send Setup > Info To Send.
3. A checkmark appears next to the fields that will be
sent. To add or remove the checkmark, select the
field.
2. Press /> Direct Send My Info.
36
3. Enter a Direct Connect number or press Browse
(left softkey) and select a number from Contacts,
Recent Calls or Memo.
3. When Ready to Send appears, press the DC button
to send the contact information.
To start a call by sending contact information:
1. From Contacts, highlight or select an entry.
2. Press /> Send Via... > Send via PTT.
4. When Ready to Send appears, press the DC button
to send the information.
Sending Contact Information
If the Contacts entry you scrolled to is a Group, you
may be prompted to allow yourself to be a part of the
group being sent. Press Yes (left softkey) to become
part of the group.
Note
You can send contact information by selecting a
Contacts entry.
Contacts entries that contain only addresses cannot be
sent. When Contacts entries are received, they do not
include ring tones or pictures.
3. Enter a Direct Connect number or press Browse
(left softkey) and select a number from Contacts,
Recent Calls or Memo.
To send contact information during a call:
4. When Ready To Send appears, press the DC button
1. While in a Direct Connect call, press /> Contacts.
to send the contact information.
2. Highlight a Contacts entry and press />
Send Via... > Send via PTT.
Receiving My Info or Contact Information
When you receive My Info or contact information from
another phone, an icon appears on the display.
If the Contacts entry you scrolled to is a Group, you
may be prompted to allow yourself to be a part of the
group being sent. Press Yes (left softkey) to become
part of the group.
Note
My Info
d
Contact Information
j
37
To view the information while still in the Direct Connect call:
Press /> View Contact.
4. When Ready To Send appears, press the DC button
to send the contact information.
ᮣ
To send a Group from Contacts:
You can also view My Info from other phones on the
1. From Contacts, highlight a Group and press />
Send Via....
Sending Groups Using Direct Send
2. To include yourself in the Group, press Yes (left
softkey). To exclude yourself, press No (right
softkey).
You can send a Group using Nextel Direct Send so that
the person who receives the Group can use the list.
To send a Group from the Recent Calls list:
3. Select Send via PTT.
4. Enter a Direct Connect number or press Browse
(left softkey) and select a number from Contacts,
Recent Calls or Memo.
1. From Recent Calls, highlight a Group and press
/> Send Group.
2. To include yourself in the Group, press Yes (left
softkey). To exclude yourself, press No (right
softkey).
5. When Ready To Send appears, press the DC button
to send the Group.
The Group will appear in the Recent Calls list on the
phone to which you sent the Group.
If you choose to include yourself and the Group
already contains 20 members, you will be prompted
that the list is full. You will be excluded from the list.
Note
3. Enter a Direct Connect number or press Browse
(left softkey) and select a number from Contacts,
Recent Calls, or Memo.
38
Group
Talkgroup
Talkgroup Calls
Setup
Dynamically,
via your phone Nextel administrator
using Talkgroup
Predefined, via
A Talkgroup is a predetermined group of Direct
Connect users, created by an account administrator.
Talkgroups can contain up to 100 members.
Management
Voice Activated
Dialing
Yes
No
Difference Between Group Connect and
Talkgroup Calls
Joining a Talkgroup
In a Group Connect call, you or another caller
determines who can participate in the call. By contrast,
participation in a Talkgroup is determined by an
administrator. Here are the ways Group Connect and
Talkgroup calls differ.
To participate in a Talkgroup, the account administrator
must first add you to the membership and then you
must “join” the Talkgroup.
1. Press Contcs (right softkey) and highlight a
Talkgroup.
Group
Talkgroup
2. Press Join (left softkey).
Group Icons
Geography
)
r
You can now receive communications from other
members of this Talkgroup.
Nationwide
Limited to local
market and network
(fleet)
You will hear all active Talkgroup conversations on your
phone. To silence them, press /> Settings >
DC/GC Options > Tkgrp Silent and then select On.
Maximum
Group Size
21 (including 100
originator)
39
During and immediately after a Talkgroup call ends,
press Options (right softkey). Your phone displays
actions you can take at this time.
Adding More Talkgroups
You can be included in additional Talkgroups by doing
one of the following:
ⅷ Using Talkgroup Management at www.nextel.com. You
must be an account administrator to use Talkgroup
Management.
Call Alerts
Call Alerts let you notify others that you want to
communicate with them using Nextel Direct Connect.
When a user receives a Call Alert, the phone sounds a
tone and displays your name or Direct Connect
number.
ⅷ Contacting your Nextel Sales Representative at the
time of activation.
Making Talkgroup Calls
1. Press
and then enter the Talkgroup number.
#
Sending Call Alerts
– or –
1. Enter a Direct Connect number and press Alert
(left softkey).
Select the Talkgroup from Contacts or the Recent
Calls list.
2. When “Ready to Alert” appears, press the DC
button to send the Call Alert.
2. Press the DC button and continue as if making a
Direct Connect call.
You can send a Call Alert from Recent Calls or
Contacts. Select a Direct Connect number and
continue as explained above.
Note
Receiving Talkgroup Calls
ᮣ
Answer it as you would a regular Direct Connect
call. Only one person at a time may speak on a
Talkgroup call.
40
Viewing Call Alerts
1. Press /> Call Alert.
2. Scroll through the list.
Responding to a Call Alert
You can set a distinctive ringer for Call Alerts. See
Note
To answer a Call Alert:
Viewing Call Alert Date and Time
1. Press /> Call Alert.
ᮣ
Press the DC button to make a Direct Connect call
to the sender.
2. Select a Call Alert and press r.
To clear a Call Alert:
Press Clear (right softkey).
To store a Call Alert in the Call Alert queue:
Responding to Call Alerts in the Queue
ᮣ
After you queue a Call Alert, you can respond to it by
making a Direct Connect call to the sender or sending
a Call Alert to the sender.
ᮣ
Press Queue (left softkey).
The Recent Calls list also stores Call Alerts you have
To make a Direct Connect call to the sender:
Note
received. They appear as Direct Connect calls. Call
Alerts remain in your Recent Calls list until you delete
them or until they reach the end of the list.
1. Press /> Call Alert.
2. Highlight a Call Alert and press the DC button to
begin the call.
Using the Call Alert Queue
This removes the Call Alert from the queue.
To send a Call Alert to the sender:
1. Press /> Call Alert.
When you queue a Call Alert, it remains in the Call Alert
queue until you make a Direct Connect call to the
sender or delete it.
41
2. Highlight a Call Alert and press Alert (left softkey).
You can make:
Ready to Alert appears on the display.
ⅷ Code calls – two-way radio calls conducted off the
network and using open channels and codes. In
these calls, anyone using your same channel and
code can hear your conversation.
3. Press the DC button until Alert Successful appears
on the display.
Deleting Call Alerts
ⅷ Private calls – two-way radio calls conducted off the
network and using the wireless phone numbers of
the participants. In these calls, others using the same
channel cannot listen in.
To delete a Call Alert from the queue:
1. From the Call Alert queue, highlight a Call Alert
and press /> Delete.
When using Direct Talk mode, the two phones should
be a minimum of six feet apart to maximize
performance and improve transmission range. You can
only make Direct Talk calls to users located within your
range. This varies according to terrain, man-made
structures, and atmospheric conditions.
2. Press ror press Yes (left softkey) to confirm.
To delete all Call Alerts from the queue:
1. From the Call Alert queue, press /> Delete All.
2. Press ror press Yes (left softkey) to confirm.
Most traditional phone features are not available in
Direct Talk mode, including on-network phone calls;
Direct Connect, Group Connect, Talkgroup calls, and
Call Alerts; data services; messaging; call timers; and
call forwarding.
Direct Talk
Nextel Direct Talk allows for two-way radio
communication “off the network” between two or more
phones equipped with this capability. This feature is
useful in areas without network coverage.
42
To set a channel and code:
Setting Your Phone to Direct Talk
1. In Direct Talk mode, press Edit (left softkey) >
Channel, and then select a channel.
Before you and another caller can use Direct Talk, both
of your phones must be set to Direct Talk mode.
2. Select Code and select a code.
1. Press /> Direct Talk.
3. Press Back (right softkey) to return to the Direct Talk
standby screen.
2. Select Go To Direct Talk.
After a few seconds, your channel and code appear on
the display screen. Your phone displays the last
channel and code used for Direct Talk.
Making and Receiving Code Calls in Direct Talk
Mode
To return to network mode from Direct Talk:
1. Press /> DT Options.
ᮣ
In Direct Talk mode, press and hold the DC button.
Your phone displays Transmitting, along with the
channel and code selected.
2. Select Exit Direct Talk.
The tone emitted from your phone when making a
Direct Talk call sounds different from the tone heard on
Direct Connect calls conducted on the network.
After a few seconds, your phone returns to network
service.
If you receive an error message, this means:
ⅷ There may be no parties on your channel or code.
ⅷ You are out of range.
Code Direct Talk Calls
To make Direct Talk Code calls, both parties must be
on the same channel and code and have their phones
set to Direct Talk. Anyone within range who is set to the
same code and channel can hear all conversations.
When you receive a Code call using Direct Talk, your
phone displays Receiving, along with the channel and
code selected. Reply as on a Direct Connect call.
43
Making a Private Direct Talk Call
Private Direct Talk Calls
You can make Private Direct Talk calls to any person on
your same channel. You do not need to set your phone
to Private Only.
Private Direct Talk allows you to silence all the calls on
a channel that are not directed specifically at you. To
do this, you must first set your phone to Private Only.
To make a private Direct Talk Call:
To set your phone to Private Only:
1. In Direct Talk mode, enter a ten-digit wireless
phone number. (You can also select a number
from Contacts or Recent Calls.)
1. In Direct Talk mode, press Edit (left softkey) >
Code > Pvt Only.
2. Press Back (right softkey) to return to the Direct Talk
standby screen.
2. Make the call in the same way you make a regular
Direct Connect call.
To reach you, other Direct Talk callers must be on your
same channel and dial your ten-digit wireless phone
number to reach you.
If you receive an error message, it means:
ⅷ You may not be using a valid wireless phone
number.
You do not need to set your phone to Private Only to
receive Private calls. If you are on the same channel as
your caller, you can receive Private Direct Talk calls.
Note
ⅷ The person that you are trying to reach may not be in
Direct Talk mode.
ⅷ The person that you are trying to reach is set to a
different channel, or is out of range.
44
Receiving All Calls on a Channel
Making Emergency Calls While in Direct
Talk Mode
You can set your phone to receive all Direct Talk
transmissions that are within range and set to the same
channel. Do this by selecting Receive All, instead of a
code.
If you attempt to make an emergency 911 call while in
Direct Talk mode, your phone automatically exits Direct
Talk mode and attempts to find a network signal.
You cannot initiate a call when the code is set to
Receive All. If you press the DC button to initiate a
Direct Connect call and your code is set to Receive All,
you receive an error message.
If you are out of network coverage, your phone cannot
make an emergency 911 call until you return to a
network coverage area. You must wait until the phone
reconnects to a network before attempting to make an
emergency 911 call.
To set the code to Receive All:
1. In Direct Talk mode, press Edit (left softkey) >
Code > Receive All.
2. Press Back (right softkey) to return to the Direct Talk
standby screen.
45
Message Center
4. Service Features:
The Basics
The message center manages your messages. You
can listen to or view voicemail messages, Multimedia
Messaging Service (MMS) messages (which include
most phone-to-phone text messages), Net alerts, and
SMS text messages in the message center.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ The message center also lets you create and send
MMS messages, including phone-to-phone text
messages. It stores messages you have sent and lets
you save drafts of messages you are creating.
Accessing the Message Center
ᮣ
Press /> Messages.
Message Center Options
After accessing the message center, select an option:
ⅷ [Create Message] — begin creating an MMS message.
ⅷ Voice Mail — access received voicemail messages.
ⅷ Inbox — access received MMS and SMS messages.
ⅷ Drafts — access MMS messages you have created
and saved but not sent.
46
ⅷ Outbox — store MMS messages that were not sent.
ⅷ Net Alert — access alerts that you receive from Nextel.
ⅷ Sent Items —access MMS messages you have sent.
If you dismiss the notification, the message is not
deleted. You can access it through the message center.
If you are not on a phone call when you receive a
message, your phone sounds a notification tone every
30 seconds until you access the message, you dismiss
the notification, or the alert time-out expires.
Receiving Messages
When you are on a phone call, you can receive
message notifications for all types of messages except
MMS messages. For other types of messages, your
phone may sound a notification tone during the call or
after you end the call, depending on how you set your
notification options.
When you receive a voicemail message, Multimedia
Messaging Service (MMS) message, text message
(SMS), or Net alert, you have two ways to access the
message:
ⅷ Respond to the message notification that appears
when the message is received.
For information on notification options, see “Setting
ⅷ Dismiss the message notification and access the
message later through the message center.
Retrieving Your Messages
Message Notifications
1. Press /> Messages.
When you receive a message, your phone notifies you
with text on the display, the Message LED on the front
of the phone, and a notification tone or vibration. You
can access the message or dismiss the notification.
2. Highlight a message type and press r.
ᮣ
To dismiss the message notification, press Later
(right softkey).
47
If you are setting up your voicemail from a phone other
than your Motorola Clutch i465, dial your ten-digit
Nextel PTN. When you hear the greeting, press *to
access your voicemail box. The system will prompt you
to enter your password. Enter the last seven digits of
your Nextel PTN. For example: 5557777. This is your
temporary password. Follow the system instructions to
complete your mailbox setup.
Voicemail
To receive voicemail messages, you must first set up
your voicemail box.
Tip
If you are bringing your phone number from another
carrier, we suggest you set up your voicemail box
after the number you brought to Nextel is active on
your Nextel phone and your temporary phone
number is deactivated. If you set up your voicemail
box prior to this, all messages and all settings
(including your greeting and password) will be lost
when the number you have brought to Nextel
becomes active.
You are in the main voicemail menu when you hear the
voicemail system options.
For details on using your voicemail, follow the audio
prompts provided by the voicemail system.
Playing Messages
Setting Up Your Voicemail Box
ᮣ
When you receive a new voicemail message, you
can either listen to it immediately by pressing Call
(left softkey), or later by pressing Back (right
softkey).
Using your Motorola Clucth i465 phone, dial your ten-
digit Nextel Personal Telephone Number (PTN). For
example: 7035557777. Follow the system instructions
to create a new four- to seven-digit password, record
your name, and record a greeting. When the system
says, “Thank you for using Nextel Voicemail,” your
mailbox is set up.
ᮣ
To listen to your voicemail messages after
dismissing the onscreen prompt, press />
Messages > Voice Mail. You will be connected to your
voicemail box.
48
To open a message on the current page:
Highlight a message and press r.
Multimedia Messages M(MMS)
ᮣ
Multimedia Messaging Service (MMS) lets you send
and receive messages that may include text, pictures,
and audio recordings.
Creating and Sending Messages
Each message you create may contain the following
fields:
Your MMS address is [email protected].
Your PTN is your ten-digit Nextel Personal Telephone
Number.
ⅷ To — the phone numbers or email addresses of one
or more recipients.
ⅷ Mesg — the body of the message. This may include
text, pictures, ring tones, or voice records.
Most common phone-to-phone text messages are
sent and received as MMS messages on your
Motorola Clutch i465 phone. Text messages sent
from other phones or mobile devices to your phone
number arrive as MMS messages.
Note
ⅷ Subject — the subject line.
ⅷ Attach — one or more attachments. These may be
pictures, ring tones, or audio files, including voice
records that you create while creating the message.
Accessing MMS Messages
ⅷ Cc — the phone numbers or email addresses of
additional recipients.
1. Press /> Messages.
2. Select Inbox (also includes SMS messages), Drafts,
ⅷ Auto Replies — lets you insert replies the recipient can
choose from when replying to your message, if the
recipient’s phone also has this feature.
or Sent Items.
Ⅲ If you have more than 9 messages, scroll right or
left to display the next or previous page.
ⅷ Priority — sets the message priority to normal or high.
ⅷ Valid Until — sets a date after which no more attempts
are made to deliver the message.
49
To send a message, you must address it to at least one
recipient. All other message fields are optional and you
can fill them in any order.
To cancel the message at any time:
ᮣ
At the message screen, press Cancel (right softkey)
or press . to cancel the message and save it in
Drafts.
Entering Text
Creating a Message
In message fields that require you to enter text, you can
begin entering the text from the keyboard when the
field is highlighted.
1. Press /> Messages > [Create Message].
Press ( L) from standby mode to begin a
Shortcut
While entering text, press /to choose a text input
mode from the context-sensitive menu. (See “Entering
new message.
You can also select [Create Message] from Inbox,
Drafts, or Outbox or begin messages from Contacts,
Recent Calls, Media Center, or standby mode, or by
replying to a message in your inbox.
Tip
Message Size
You can create and send messages of up to 100 KB,
including attachments for MMS and Message Group
size of the message appears at the top of the display
as you are creating the message.
2. Address the message:
Ⅲ Select To. Enter the phone number or email
address from the keypad and press r. Repeat
this action to enter more phone numbers or email
addresses.
Sending or Canceling
– or –
To send the message at any time after it has been
addressed:
PressSearch (left softkey) to select recipients from
Contacts or Recent Calls. Highlight recipient(s),
ᮣ
Press Send (left softkey) or press /> Send.
50
press rto select them (entries will be checked),
and then press Done (left softkey).
Adding More Message Options
1. To view more fields in a message, scroll to MORE
and press r.
To remove a phone number or email address from
the list of message recipients, highlight the phone
number or email address and press Remove (left
softkey).
Tip
2. To create or edit the subject line, select Subject,
enter a subject, and press r.
3. To add CC’s, select Cc and add recipient(s).
3. To enter or edit the body of the message:
4. To insert replies the recipient can choose from
when replying to your message, select Auto Replies.
Ⅲ Select Mesg and then use any of the following
options to enter your message.
Ⅲ Enter text from the keyboard or select a Quick
(right softkey) when you are finished.
If you have created a signature, the signature
automatically appears in this field. Text you enter
appears before your signature. (See “Adding a
Note
5. To set the priority of the message, select Priority
and then select a setting.
● Enter text from the keyboard.
6. To set a date after which attempts to deliver the
message end:
Ⅲ Select Valid Until, enter a date, and
press r.
● Insert a picture, a ring tone, or an audio file.
Ⅲ To set no date, press No Date (left softkey).
When you are finished, press r.
7. To send the message, press Send (left softkey) or
press /> Send.
4. To send the message without additional options,
press Send (left softkey) or press /> Send.
51
Replying to a Message
If the message you are replying to was sent with auto
replies, it contains a numbered list of possible replies.
Press the number of a reply. The reply is sent
immediately without any further action.
Note
You can reply to a read message while you are viewing
it or while it is highlighted in the Message Center. You
cannot reply to unread messages.
More Ways to Begin a Message
When you reply to a message, some of the fields in
your reply are filled in automatically. These may include
To, Message (the first 40 characters of the received
message), Subject, and Cc.
In addition to beginning a message from the Message
Center, you can begin a message from Contacts, the
Recent Calls list, standby mode, or the Media Center.
To reply to a message:
To begin a message from Contacts:
1. Display or highlight a read message and press
Reply (left softkey). (To reply to the sender and all
recipients, press /> Reply All.)
1. From the Contacts list, highlight an entry.
2. Scroll left or right to view the Contacts types until
you see the icon for the phone number or email
address to which to send the message.
2. Select [Create Reply] and enter a reply message or
select a short reply from the list.
3. Press Create (left softkey) or press /> Create
Message.
3. Edit any applicable message fields and press r.
4. Press Send (left softkey).
4. Create and send the message.
To create new reply phrases to use in later reply
messages, see “Quick Notes and Reply Phrases” on
Tip
52
To begin a message from the Recent Calls list:
called Quick Notes. After you add Quick Notes, you
can edit them as you would any other text.
1. From the Recent Calls list, highlight an entry.
To insert a quick note:
2. If the entry has more than one phone number
stored, display the phone number to which to send
the message.
1. While you are creating a message, highlight or
select Message or Subject and then press QNotes
(left softkey).
3. Press Create (left softkey) or press /> Create.
4. Create and send the message.
2. Select a Quick Note to insert into the message.
To add a quick note after you have already started
entering a message, press /> Insert >
Add QNotes, and select a note.
Tip
To begin a message from standby mode:
ᮣ
Enter a phone number and press />
Create Message.
To create new Quick Notes to use in later messages,
To begin a message from the Media Center:
1. From the Media Center, highlight or select a picture
or audio file.
Inserting Pictures
You can insert pictures from Media Center. If the
forward locked icon (X) appears next to a file, it cannot
be included in a message.
2. Press Send (left softkey).
3. Create and send the message. The selected file is
automatically included as an attachment.
1. Highlight the Message field and press />
Add Picture. (You will see a list of available pictures.)
Quick Notes
2. Highlight a picture and press r.
When you are filling in the Message and Subject
message fields, you can add preset words or phrases
53
2. Press Delete (left softkey).
You can also attach items to messages by selecting
Inserting Audio Files or Voice Records
Note
You can insert audio files from the Media Center or
voice records from your voice records list. Preloaded
audio files or files with the forward locked icon (X)
cannot be included in a message.
MORE and then selecting Attach.
Message Groups
1. Highlight the Message field and press />
Insert Audio. (You will see a list of available audio
files.)
A Message Group allows you to send Multimedia
Messaging Service (MMS) messages to groups of up
to 20 contacts.
To hear an audio file before inserting it, highlight the
file name and press Preview (left softkey).
Tip
Creating a Message Group
1. Press /> Contacts > [New Msg Group].
2. Highlight an audio file or voice record and
press r.
2. Highlight Name and press r.
3. Type a name for the Message Group or press
Browse (left softkey) to select a name from the
Name Browser and press r.
Ⅲ To record a voice record, select Record Voice and
record a new voice record.
Removing an Inserted Item
4. Highlight [Add Member] and press r.
To remove an item inserted into a message:
5. From Contacts select entries to add to the
Message Group and press r.
1. Select the Mesg field and highlight the item by
scrolling to the right.
6. Press Done (left softkey) and then press Save
(left softkey) to save members to the message
group.
54
Viewing Members of a Message Group
Sending a Message to a Message Group
1. Press /> Messages > [Create Message].
2. Press Search > Contacts.
ᮣ
Press /> Contacts, select the Message Group and
press r.
Deleting a Message Group
3. Select a Message Group, press r, and then press
Done.
1. Press /> Contacts and select the Message Group.
2. Press /> Delete Msg Group.
4. Enter the text from the keyboard or use a Quick
3. Press Yes (left softkey) or rto delete.
5. Press Send (left softkey) to send the message to
the group.
Removing a Member From a Message Group
1. Select the Message Group in contacts and press
/> Edit.
Drafts
While you are creating a message, you can save it in
Drafts before you send it. You can view, edit, send, or
delete saved drafts.
2. Highlight the member you wish to remove and
press /> Remove Member.
Adding a Member to a Message Group
Saving a Message in Drafts
1. Select the Message Group in contacts and press
/> Edit.
ᮣ
While you are creating a message, press />
Save and the message will be saved in drafts.
2. Select [Add Member], select the member you want
to add, and then pressr > Done > Save.
After saving, you can continue to create the message.
The version you saved in Drafts will not change.
55
2. Highlight a message and press Resend (left
Accessing Saved Drafts
softkey).
ᮣ
Press /> Messages > Drafts.
If your message was sent successfully, Resend will
Note
not appear as an option.
Sent Items
The Sent Items folder holds all messages that have
been sent.
Receiving a Message
When you receive an MMS message, a message
notification appears on the display.
Forwarding Sent Items
1. Press /> Messages > Sent Items.
2. Highlight a message and press /> Forward.
3. Edit and send your message.
To view the message:
ᮣ
Press ror press Read (left softkey). The message
is downloaded from the message server.
To dismiss the message notification:
Press Later (right softkey).
Outbox
ᮣ
Messages you tried to send are stored in the Outbox.
This icon 2 appears on the display, reminding you that
Resending Messages
you have a new message.
If a message was not sent from your phone, you can
resend it.
Threaded Inbox
The threaded inbox allows you to organize your
messages by subject or sender.
1. Press /> Messages > Outbox.
1. From your inbox highlight a message.
56
2. Press / > Threading and select None, Subject or
Sender.
Actions for Received Messages
Deleting
Navigating a Message
To delete unread messages:
As you scroll through a message, numbers, email
addresses, and Web addresses are highlighted.
1. Highlight a message and press Delete (left softkey).
2. Press ror press Yes (left softkey) to confirm.
To delete read messages:
Pictures and audio recordings are also highlighted.
Embedded Objects and Attachments
1. Highlight or view a message and press />
Delete Message.
Messages may contain pictures or audio files as part of
the body of the message or as attachments.
2. Press ror press Yes (left softkey) to confirm.
If a message contains pictures or audio files in the
body of the message, highlight each picture or audio
file to view or play it.
Forwarding
1. Highlight or view a message and press />
Forward.
If a message contains a picture or audio file as an
attachment, highlight the attachment and press rto
view the picture or play the audio file.
2. Create and send your message.
Embedded objects and attachments are included
when you forward a message.
Audio files in messages do not play if VibeAll is set to
On.
Note
57
3. Press the DC button.
Locking and Unlocking
To make a Talkgroup call to a Talkgroup ID in a message:
1. View the message.
When you lock a message, it cannot be deleted until
you unlock it.
ᮣ
Highlight or view a message and press />
Lock Message or Unlock Message.
2. Highlight a Talkgroup ID and then press />
Talkgroup.
Calling a Number in a Message
3. Press the DC button.
If any field in a message contains a phone number,
Direct Connect number, or Talkgroup ID, you can call
or send a Call Alert to that number.
Storing Message Information to Contacts
If a message you receive contains a phone number,
Direct Connect number, Talkgroup ID, or an email
address in any of the fields, you can store this
information to Contacts.
To make a call to a number in a message:
1. View the message.
1. View the message.
2. Highlight a number and press , to make a
phone call or press the DC button to make a Direct
Connect call.
2. Highlight a number or email address and then
press /> Save Number or Save Email.
To send a Call Alert to a Direct Connect number in a
message:
3. Select [New Contact] to store the number in a new
entry, or select an entry to store the information to
an existing entry.
1. View the message.
4. With the Contacts type field highlighted, scroll left
or right to display a Contacts type for the number
or email address.
2. Highlight a Direct Connect number and then press
press /> Alert.
58
5. Press Save (left softkey).
Your phone's SMS address is [email protected].
Your PTN is your ten-digit Personal Telephone Number.
Going to a Website
Most traditional phone-to-phone text messages
arrive as MMS messages on your MotorolaClutch
i465 phone. Your phone can send and receive MMS
messages.
Note
If a message contains one or more Web addresses,
you can go to the website.
1. View the message.
Your phone can receive SMS text messages, but it
cannot send them.
2. Highlight a Web address and then press />
Go To Website.
Accessing Text Messages
The entire Web address must appear in the
message. Otherwise, you cannot go to the website.
Note
ᮣ
When you receive a text message, you will see an
alert. Press Read (left softkey) to display the
message.
Saving Attachments or Embedded Files
1. View a message.
Caller ID Blocking
2. Highlight an attachment or an embedded picture
or audio file and then press /> Save Picture,
Save Audio or Save Attachment.
Caller ID allows people to identify a caller before
answering the phone by displaying the number of the
incoming call. If you do not want your number
displayed when you make a call, follow these steps.
Text Messaging (SMS)
With text messaging (SMS), you can receive instant text
messages from another messaging-ready phone or
from an email account.
59
If you are on a call and receive a second call, your
phone emits a tone and displays a message.
Per-Call Blocking
To block delivery of your number for a single phone call:
To accept the second call and put the active call on hold:
ᮣ
Press *67before dialing the call.
ᮣ
Press Yes (left softkey).
Your Nextel phone number cannot be blocked from
calls made to 911, 800, 855, 866, 877, 888, or other
toll-free phone numbers.
To accept the second call and end the active call:
1. Press .. Your phone rings with the second call.
2. Answer the second call.
Per-Line Blocking
To decline the second call:
You can request that Nextel Customer Service
permanently block delivery of your phone number on
every call you make. In this case, you may need to
display your number for certain calls.
ᮣ
Press No (right softkey). If you subscribe to
voicemail, the call is forwarded to your voicemail
box, unless you set Call Forward or If Busy to a
different number.
To show your number on a per-call basis:
Turn Off Call Waiting
ᮣ
Press *82before dialing the call.
To turn off Call Waiting before a call:
Call Waiting
ᮣ
Press *70before dialing the call. Call Waiting
is reactivated once the call ends.
Call Waiting lets you receive a second call while on an
active call. Call Waiting is always available, unless you
turn it off for a specific call.
60
To turn off Call Waiting during a call:
Making a Three-Way Call
ᮣ
Press /> In Call Setup > Call Waiting > Off.
With Three-Way Calling, you can talk to two people at
the same time. When using this feature, the normal
airtime rates will be charged for each of the two calls.
To turn Call Waiting back on while still on the call, set
this option to On.
Tip
1. During an active phone call, press /> 3 Way.
(The first call is placed on hold.)
Making a Second Call
2. Enter a second phone number and press ,.
1. Place or receive a phone call.
3. Press Join (right softkey).
2. While the call is active, press /> 2nd Call. (The
first call is placed on hold.)
If one of the people you called hangs up during the
call, you and the remaining caller stay connected. If you
initiated the call and are the first to hang up, all callers
are disconnected.
3. Enter a second phone number and press , to
place the call.
For quick ways to enter the number, press /.
Note
To end the second call and make the on-hold call active:
Press .
To merge two calls into a three-way call:
1. During an active phone call, press /> 2nd Call.
(The first call is placed on hold.)
ᮣ
2. Enter a second phone number and press ,.
To make the on-hold call active and put the active call on
hold:
3. Press /> Join.
ᮣ
Press Switch (right softkey).
61
Phone line 2 is active; calls to phone line 1 are
being forwarded.
Call Forwarding
&
'
%
Phone line 2 is active; calls to phone line 2 are
being forwarded.
Call Forwarding lets you forward all your incoming calls
to another phone number – even when your phone is
turned off. You can continue to make calls from your
phone when Call Forwarding is activated.
Phone line 2 is active; calls to phone lines 1
and 2 are being forwarded.
Call Forwarding sends calls to the phone numbers you
specify. You can forward all calls to one number or
forward missed calls to different numbers depending
on the reason you missed the call.
To forward all calls:
1. Press /> Call Forward > Forward All Calls.
2. Select To.
Ⅲ If you specified a forwarding number for all calls
Forwarding All Calls
before, this number appears.
When you set your phone to forward all calls, an icon
appears in the top row of the display:
Ⅲ To forward calls to this number, highlight it and
press r.
Ⅲ To delete this number, press rand then press
and hold Delete (left softkey).
Phone line 1 is active; calls to phone line 1 are
being forwarded.
"
Phone line 1 is active; calls to phone line 2 are
being forwarded.
3. To enter a forwarding number:
#
Ⅲ Enter the number or press Search (left softkey),
select Contacts, Recent Calls or Memo and then
select a number.
Phone line 1 is active; calls to phone lines 1
and 2 are being forwarded.
!
62
4. Press r. All your calls are now forwarded to the
To forward missed calls:
number you specified.
1. Press /> Call Forward > Forward All Calls > Detailed.
Turning Off Call Forwarding
1. Press /> Call Forward > To.
2. Set this option to Off.
If your phone is set to forward all calls, you must first
turn off call forwarding to access this option. (See
Note
2. Select If Busy to specify a forwarding number for
calls received when your phone is busy.
All your calls are now sent to your phone.
Forwarding Missed Calls
3. If you specified a forwarding number for this type
of call before, this number displays.
Calls you miss are forwarded according to the options
set for missed calls. By default, missed calls are
forwarded to voicemail.
Ⅲ To forward calls to this number, highlight it, press
Ⅲ To delete this number, press r, and then press
and hold Delete (left softkey).
You can specify a forwarding number for each type of
missed call:
4. To enter a forwarding number:
ⅷ If Busy — Your phone is on a call or transferring data.
Ⅲ Enter the number or press Search (left softkey),
select Contacts, Recent Calls or Memo and then
select a number.
ⅷ If No Answer — You do not answer on the first four
rings.
ⅷ If Unreachable — Your phone is out of coverage or
powered off.
5. Press r.
6. Repeat step 2 through step 5 for If No Answer and
If Unreachable.
You are charged a higher rate for calls you have
forwarded.
Note
63
7. When you are finished, press Back (right softkey).
Telecommunications Relay Service
Nextel supports services for communicating with
speech and/or hearing impaired individuals. You can
dial 711 to reach a local Telecommunications Relay
Center. You will then be connected to your destination
number. Relay service works through a
Communications Assistant who reads messages typed
into a TDD/TTY device by a speech or hearing
impaired individual to you. The Communications
Assistant then types your spoken messages to the
hearing or speech impaired individual.
Making International Calls
Your service default is “International Calls Restricted.”
Contact Nextel Customer Service to obtain
international dialing access.
Calls placed between the United States and Canada
do not require an international access code.
Special Dialing Codes
Telecommunications Relay Service is available 24
hours a day, seven days a week, and every call is
strictly confidential.
Non-Emergency Numbers
Using 711 to reach Telecommunications Relay
Service may not be available in all areas.
Note
Nextel supports many “non-emergency” numbers
(such as #77, 311, and 511) provided by local and state
governments. These numbers are used to report
non-emergency incidents. If the situation includes
imminent danger or loss of life, you should dial 911.
To enable TTY mode:
1. Press /> Settings > Phone Calls > TTY > Use TTY.
2. Select On to enable TTY mode.
64
3. For TTY options, highlight Type, press rand then
ⅷ Have two different area codes (must be in same
market) to convey a local image to callers.
select an option:
Ⅲ TTY (TeleTypewriter) – Type and read text on your
TTY.
ⅷ Use different ringer styles so that you can tell which
line is receiving a call.
Ⅲ VCO (Voice Carry-Over) – Speak into the phone
and read text replies on your TTY.
ⅷ Forward incoming calls to either your primary or
alternate line phone number.
Ⅲ HCO (Hearing Carry-Over) – Type text on your
TTY and listen to voice replies on your phone.
ⅷ Choose a Second Line Service plan that fits your
needs.
In order to activate Second Line Service, contact your
Nextel Sales Representative or call Nextel Customer
Service.
Nextel Phone Services
Contact Nextel Customer Service to obtain these
services or for additional information.
To set the active line (primary or alternate):
1. Press /> Settings > Phone Calls > Set Line.
2. Select a phone line to be active.
Some services are not available outside of the
continental United States.
Note
When incoming calls are made to a non-active line,
they will be sent to voicemail without ringing. (See “Call
Second Line Service
You can have two different phone numbers on the
same phone. With Second Line Service, you can:
ⅷ Get separate bills for each phone line.
ⅷ Bring in an existing wireless or home phone number
to Nextel to activate on the second line.
65
Sprint 411
Dial 411 from your wireless phone to receive
nationwide listings, movie listings and showtimes,
restaurant reservations, and driving directions, as well
as sports scores, stock quotes, and weather conditions.
Spanish speaking operators available. Receive up to
three phone numbers or pieces of information per call,
and be automatically connected at no additional
charge. Airtime and other charges apply.
66
Opening the Browser
ᮣ
Press /> Net or press L.
5. Data Services
Options available under the home page include:
ⅷ Business Tools – Provides access to business tools.
ⅷ Text Messaging – Provides access to text messaging.
ࡗ ࡗ ⅷ Games, Ringers, & More – Provides access to
downloadable items.
ⅷ News, Sports & More – Lets you access news services.
ⅷ Weekly Highlights – Displays Sprint weekly highlights.
ⅷ Email & IM – Allows you to send email and IMs.
Wireless Data Services
ⅷ Your Bookmarks – Allows you to access and manage
your bookmarks.
With Web access on your phone, you can browse your
favorite websites, making it easier than ever to stay
informed while on the go. Follow sports scores,
breaking news, and weather, and shop on your phone
anywhere on the Nextel National Network.
ⅷ Search – Launches a Web search.
ⅷ Go to URL – Lets you enter website addresses.
ⅷ My Account – Lets you configure and manage your
browser settings.
Using the Web Browser
ⅷ Help – Displays online help.
Navigating the Web from your phone is easy once you
get the hang of it.
67
Going to a Specific Website
Bookmarking a page does not store the page
contents, just its address.
Note
To go to a particular website by entering a Web address
(URL):
Some pages cannot be bookmarked. Whether a
particular Web page may be marked is controlled by
its creator.
1. From the home page, select Go to URL.
2. Press Edit (left softkey).
Accessing a Bookmark
From the home page:
3. Use your keyboard to enter the Web address and
press Done (left softkey).
1. Select Your Bookmarks.
4. Press Ok (right softkey).
2. Highlight a bookmark and press r(or press the
number corresponding to the bookmark).
Not all websites are viewable on your phone.
Note
Creating a Bookmark
From any other Web page:
Bookmarks allow you to store the address of your
favorite websites for easy access at a later time.
1. Press and hold /to open the browser menu.
2. Select Favorites.
1. Go to a Web page and press and hold /to open
the browser menu.
3. Select a bookmark and press r(or press the
number corresponding to the bookmark).
2. Highlight Mark page and press r.
To return to the home page from any other Web
page, press ..
Tip
3. Confirm or edit the bookmark name, highlight Save,
and then press rto save the bookmark.
68
Reloading a Web Page
Downloading Content
1. Press and hold /to open the browser menu.
Your phone arrives with Java applications and games
loaded and ready to install. You can download and
install more Java applications. For more information on
Java Security, (see “Setting Privacy for Each Java
2. Select Advanced > Reload. (The browser will reload
the current Web page.)
Restarting the Web Browser
If the Web browser seems to be malfunctioning or
stops responding, you can usually fix the problem by
simply restarting the browser.
Check the Games, Ringers, & More menu option for a
catalog of items available for purchase and download.
account for a wide selection of available Java
applications and downloading instructions.
1. Press and hold /to open the browser menu.
2. Select Advanced > Restart browser.
Using Java applications may cause your phone’s
battery power to deplete more quickly.
Note
69
Sound Settings
6. Settings
Ring Tones
Your phone provides a variety of ringer options that
allow you to customize your ring and volume settings.
These options allow you to identify incoming calls and
messages by the ring.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ Selecting Ringer Types
1. Press /> Ring Tones.
2. Scroll through the list of ring tones. A sample
ringer will sound as you highlight each option.
3. Press ror press Assign (left softkey).
4. Select the function(s) to which to assign the current
ringer by highlighting the option and pressing r.
(A check mark appears next to selected options.)
5. When you are finished, press Done (left softkey) to
assign the ringer to the selected function(s).
70
Assigning a Ring Tone to a Contact
Downloading More Ring Tones
You can also assign a ringer to a specific contact entry
so you know who's calling without looking at the
phone.
To use other ring tones, you can download them into
your phone for a fee.
ᮣ
Press /> Ring Tones > Buy Ring Tones.
1. Press /> Ring Tones.
Ring tones may be downloaded only once. If you
delete a ring tone from your phone and wish to
reassign it, you must purchase it again.
Note
2. Scroll through the list of ring tones and select one.
A sample ringer will sound as you highlight each
option
Managing Memory
3. Press ror press Assign (left softkey).
To view the amount of memory available for custom ring
tones:
4. Select A Contact....
5. Highlight a Contacts entry and press rto assign
1. Press /> Ring Tones.
the ringer.
2. Make sure Vibrate All is set to Off.
Viewing Ring Tone Assignments
1. Press /> Ring Tones.
3. Highlight any ring tone and press />
Memory Usage.
2. Make sure Vibrate All is set to Off.
Deleting custom ring tones frees memory.
3. Highlight any ring tone and then press />
Deleting Ring Tones
Overview.
Deleting a ring tone from the list deletes it from your
phone.
4. Scroll to view ring tones assigned to features and
Contact entries.
71
In most cases, when you delete a ring tone that you
purchased from your phone, you will have to purchase
it again.
Press /> Ring Tones > Vibrate All. Set this option to
On or Locked.
Setting this option to Locked requires you to press
and hold the volume control up to turn Vibrate All off.
The Locked option helps prevent you from
accidentally turning Vibrate All off.
Tip
To delete a ring tone:
1. Press /> Ring Tones.
2. Make sure Vibrate All is set to Off.
3. Highlight a ringtone and press /> Delete.
4. Press Yes (left softkey) to confirm.
To deactivate Vibrate All:
1. Press and hold the volume key up to unlock
vibrate all.
2. Press the volume key up repeatedly to select a
volume level or press /> Ring Tones > Vibrate All >
Off.
Vibrate Settings
Vibrate All
These icons indicate how the ringer is set:
The Vibrate All option allows you to be notified of calls
and messages with a vibration instead of an audible
alert.
The phone always vibrates instead of
5
6
"
making a sound.
To activate Vibrate All:
The phone vibrates instead of making a
sound for phone calls.
ᮣ
Press and hold the volume button down in standby
mode. (Pressing and holding displays “VibeAll:
On.” Continuing to hold the button down displays
“VibeAll: Locked.”
Direct Connect calls, Group Connect
calls, and Talkgroup calls are heard
through the earpiece, not the speaker.
– or –
72
To activate Silence All:
The phone vibrates then rings for all calls.
The ring volume is set to zero for all calls.
/
ᮣ
With the phone in standby mode press and hold
the volume key down until the ringer level is set
at 0. (The screen will display ,.)
,
Ring and Vibrate
To deactivate Silence All:
To set your phone to ring and vibrate when you receive
phone calls or Call Alerts:
ᮣ
Press the volume key up repeatedly to select a
volume level.
1. Press /> Ring Tones.
To set your phone to vibrate instead of making a sound for
some features but not others:
2. Make sure Vibrate All is set to Off.
3. Scroll through the list and select a ring tone.
4. Press /> Assign w/Vibe.
1. Press /> Ring Tones.
2. Make sure Vibrate All is set to Off.
3. Select Vibrate from the list of ring tones.
5. Select Phone Line 1 and/or Phone Line 2 and press
Done (left softkey).
4. Select the feature(s) to which to assign Vibrate and
press Done (left softkey).
This icon/ appears on the display.
Silence All
To set ring options for Direct Connect calls, Group
Connect calls, and Talkgroup calls, see “Vibrate
Note
The Silence All option allows you to mute all sounds
without turning your phone off.
73
Adjusting the Phone’s Volume Settings
Display Settings
Adjust your phone’s volume settings to suit your needs
and your environment.
Changing the Backlight Time Length
1. Press /> Settings > Volume.
Select how long the display screen and keyboard
remain backlit after any keypress is made.
2. Select Line 1, Line 2, Messages, Earpiece, Speaker,
Keypad, Java Earpiece, Java Speaker or Data.
1. Press /> Settings > Display/Info > Backlight.
3. Choose a volume level and press r.
2. Highlight an option, press rand then choose a
setting.
You can adjust the ringer volume in standby mode
(or the earpiece volume during a call) by using the
volume key on the left side of your phone.
Tip
Ⅲ For Timer or Java Timer, select a time.
Ⅲ For PTT Backlight, Bluetooth LED, Message LED or
VMail LED, select On or Off.
Beep
Long backlight settings reduce the battery’s talk and
standby times.
Note
Set your phone to alert you with an audible tone once
a minute during a voice call.
Changing the Display Screen
1. Press /> Settings > Phone Calls > Minute Beep.
2. Highlight On or Off and press r.
Choose what you see on the display screen while
powering on or off and when in standby mode.
1. Press /> Settings > Display/Info > Wallpaper>
Wallpaper.
74
2. Select an image and press View (left softkey) to view
it. Press Back (right softkey) to return to the
available images.
Ⅲ List View to display the menu as a list.
Changing the Theme
3. Press rto assign an image.
Customize your phone’s display appearance by
selecting a theme to reflect your personality.
Setting Wallpaper to Change Automatically
1. Press /> Settings > Display/Info > Theme.
When you set your wallpaper to change automatically,
your phone uses each of the pictures inMedia Center as
wallpaper, cycling through them at a pace you choose.
2. Highlight an option and press r.
Changing the Clock Display
1. Press /> Settings > Display/Info > Wallpaper >
Auto Cycle.
Select a format for the time and date display and
choose whether the time and date appear in standby
mode.
2. Select how frequently the wallpaper will change
then press r.
1. Press /> Settings > Display/Info > Clock.
Changing the Phone’s Menu Style
2. Select Display On/Off, Time Format orDate Format and
then press r.
Choose how your phone’s menu is displayed on the
screen.
3. Select an option and press rto apply the setting.
1. Press /> Settings > Display/Info > Menu View.
The year is set by the network, and even though it is
an option, it cannot be changed.
Note
2. Highlight an option and press r.
Ⅲ Icon View to view the main menu as a grid of
icons. Icons animate when they are highlighted.
75
also choose to be notified with a sound while making a
phone call.
Changing the Text Size
Adjust the font when entering text (for example, when
using the notepad or when adding a Contacts entry).
1. Press /> Settings > Phone Calls > Notifications.
2. Highlight Receive All, Msg Mail Only or Delay All and
1. Press /> Settings > Display/Info > Text Size.
press r.
2. Highlight an option and press r.
Delay All is the default setting.
Note
Tip
Messaging Settings
To set notification options during a call press />
In Call Setup > Notifications.
Staying connected to your friends and family has never
been easier. With your phone’s advanced messaging
capabilities, you can send and receive many different
kinds of text messages without placing a voice call.
(For more information see “Multimedia Messages
Customizing MMS
The Setup menu lets you customize MMS for your
phone:
ⅷ Signature — Enter text here to create a signature that is
automatically inserted at the end of each message.
Messaging settings make messaging easier by letting
you decide how you would like to be notified of new
messages, create a signature with each sent message,
and create your own preset messages.
ⅷ Quick Notes — lets you create new Quick Notes and
edit or delete Quick Notes you have created.
ⅷ Cleanup — controls how long messages remain in the
Inbox and Sent Items before they are deleted.
Setting Message Notification
ⅷ Delivery Rpt — allows you to set the default for the
When you receive a message, your phone notifies you
by displaying an icon on your display screen. You can
Delivery Report Option to on of off.
76
ⅷ Memory Size — displays a report on phone memory.
2. Select [New Quicknote] or [New Reply], or press
New (left softkey).
ⅷ MMS Setup — allows you to set up the following:
3. Enter text and press r.
Ⅲ Friendly Name — lets you enter the name displayed
in the From field on messages you send.
To edit a Quick Note or reply phrase:
Ⅲ Downloads — lets you control message downloads.
Automatic downloads messages automatically.
Manual requires you to reply to a prompt before
messages download to your phone.
1. From the Setup menu, select Quick Notes or
MMS Setup > Replies.
2. Select a Quick Note or reply phrase you have
created.
Ⅲ Replies — lets you create new reply phrases and
edit or delete reply phrases you have created.
3. Edit the text and press r.
To access the Setup menu:
To delete a Quick Note or reply phrase:
1. Press /> Messages.
1. From the Setup menu, select Quick Notes or
MMS Setup > Replies.
2. Highlight [Create Message] and press /> Setup.
2. Highlight a Quick Note or reply phrase you have
created.
This option is available from many context-sensitive
menus when you are using MMS.
Tip
3. Press Delete (left softkey) and then press ror
press Yes (left softkey) to confirm.
Quick Notes and Reply Phrases
To add a Quick Note or Reply phrase:
You can edit or delete only Quick Notes or Reply
phrases that you created.
Note
1. From the Setup menu, select Quick Notes or
MMS Setup > Replies.
77
Setting the Cleanup Option
The cleanup option controls how long messages
remain in the Inbox and Sent Items before they are
deleted. You set the cleanup option for the Inbox and
Sent Items separately.
Airplane Mode
Sometimes you may want to have your phone on, but
turn off its ability to make and receive calls and other
transmissions.
The cleanup option deletes only read, unlocked
messages.
To set the cleanup options:
To set your phone so that it cannot make or receive phone
calls, Direct Connect calls, Group Connect calls, Talkgroup
calls, or transfer data:
1. From the Message Center, press /> Setup >
Cleanup > Inbox orSent Items.
2. Choose a cleanup option.
1. Press /> Settings > Advanced > Transmitters.
2. Select Off and press r.
3. To automatically delete messages now, press r
or press Yes (left softkey). To delete messages later,
press No (right softkey).
3. Press Yes (left softkey).
When in Transmitters Off mode, your phone’s standby
screen displays “Transmitters Off.”
Adding a Customized Signature
Add a customized signature to each message you
send.
While powering on your phone, you can turn
transmitters off by pressing .for more than five
seconds.
Note
1. Press /> Messages> /> Setup > Signature. If you
do not wish to attach a signature to your outgoing
messages, press Delete (left softkey).
78
To restore your phone’s ability to do all these things:
Headset Options
ᮣ
Set this option to On and then press Yes (left
softkey).
To set your phone to send incoming sound to a headset
only, or to a headset and a speaker at the same time:
When Transmitters is set to Off, your phone’s
Bluetooth capability is disabled, and all active
Bluetooth connections are dropped.
Note
1. Press /> Settings > Advanced > Headset/Spkr.
2. Select HdsetOnly to send incoming sound to the
headset only.
Setting One Touch Direct Connect
– or –
Select Hdset&Spkr to send incoming sound to the
headset and ring tones to the speaker.
One Touch Direct Connect sets your phone to call the
most recent Direct Connect number or Group on the
Recent Calls list, or a Direct Connect number you
choose, every time you press the DC button.
Profiles
1. Press /> Settings > DC/GC Options > One Touch DC.
A profile is a group of settings saved together so that
you can apply them to your phone easily.
2. Select from Off, Quick PTT, Last Call, Assigned No.,
Send Picture, Send My Info or Send Contact and
press r.
Your phone arrives with preset profiles. You can also
create your own profiles.
If you are entering a Talkgroup number, enter #
before the number.
Tip
79
When you do this, your phone either:
Viewing Profiles
ⅷ Updates the profile in effect to reflect these changes,
without notifying you.
To view the profiles stored in your phone:
1. Press /> Profiles.
– or –
ⅷ Creates a temporary profile that contains these
changes.
2. Highlight a profile and press r.
The profile that is currently in effect on your phone
has a checkmark next to it.
Tip
To set your phone to create a temporary profile that contains
changes you make to settings:
3. Scroll to view settings.
1. Press /> Profiles.
Switching Profiles
2. Press /and then select Setup > Temp Profile.
3. Set this option to On.
1. Press /> Profiles.
2. Highlight a profile and press r.
The profile you selected is now in effect.
To set your phone to update the profile in effect to reflect any
changes you make to settings:
ᮣ
Set Temp Profile to Off in step 3 above.
How Changing Settings Affects Profiles
Temporary Profiles
Many of the settings contained in profiles can be set
without switching or editing profiles — for example, by
selecting Settings or Ring Tones to set options, or by
setting the volume of the phone’s ring using the
volume controls.
If your phone is set to create temporary profiles, a
temporary profile is created when you make changes
to settings without switching or editing profiles. These
stay in effect until you switch profiles or power off your
phone.
80
Temporary profiles and any settings you have changed
are marked with asterisks (*).
2. Enter a name and press r.
3. To base this profile on an existing profile, select
Copy From and then select a profile and press r. If
you do not choose a profile to copy from, the new
profile is based on a default profile.
Storing a Temporary Profile
To store a temporary profile as a new profile:
1. Press /> Profiles.
4. Press Create (left softkey).
2. Highlight the temporary profile and press />
Store As New.
5. Scroll through the list of options and set their
values.
3. Enter a name and press r.
To overwrite the profile the temporary profile is based on:
1. Press /> Profiles.
6. When you are finished, press Done (right softkey).
Editing Profiles
1. Press /> Profiles.
2. Highlight the temporary profile, press
/> Store Changes, and then press Yes
(left softkey).
2. Highlight a profile, press /and then select Edit.
3. Scroll through the list of options and set their
values.
The temporary profile is stored with the name of the
profile it is based on. The profile it is based on, as it
existed before you made changes to settings, is
gone.
Note
4. When you are finished, press Done (right softkey).
Deleting Profiles
To delete a profile:
Creating Profiles
1. Press /> Profiles.
1. Press /> Profiles > [New Profile].
81
2. Highlight a profile, press /and then select Delete.
3. Press ror press Yes (left softkey).
To delete all profiles:
entries. When you are finished, press Done
(right softkey).
Ⅲ DC/GC – sets filtering options for Direct Connect
calls and Talkgroup calls.
1. Press /> Profiles.
●
Off – notifies you of all DC and Talkgroup calls.
●
On – ignores all DC and Talkgroup calls.
2. Press /and then select Delete All.
3. Press ror press Yes (left softkey) to confirm.
Ⅲ Group – sets filtering options for Group Connect
calls.
Setting Call Filtering
●
Off – notifies you of all Group Connect calls.
●
On – ignores all Group Connect calls.
The call filtering setting in each profile lets you control
which calls, Call Alerts, and message notifications your
phone notifies you of, and which it ignores.
Ⅲ Alerts – sets filtering options for Call Alerts.
●
Off – notifies you of all Call Alerts.
1. While setting options for a profile, select Call Filter.
●
On – ignores all Call Alerts.
Ⅲ Notifications – sets filtering options for message
notifications.
2. Select a filtering option
Ⅲ Phone – sets filtering options for phone calls.
●
●
●
●
Off – notifies you of all messages.
Voice Messages – ignores all voice messages.
Text Messages – ignores text messages.
All – ignores all messages..
●
●
●
Off – notifies you of all calls.
All – ignores all calls.
All Contacts – notifies you only of calls from
Contacts.
●
Some Cntcs – notifies you only of calls from
selected Contacts. Select up to five Contacts
82
2. Press and hold /until a confirmation screen
The message notification screen still appears when
you receive a message you have set not to sound a
tone or vibrate.
Note
appears.
3. Press ror press Yes (left softkey).
4. Select Key.
3. Press Done (right softkey).
5. Press a number key for the shortcut and press r.
Phone Setup Options
6. To record a voice name for the shortcut, select
Voice (optional). Follow the prompts to say and
repeat the name. Speak clearly into the
microphone.
Shortcuts
Your phone offers you the option of assigning shortcuts
to favorite or often-used functions. Pressing the /key
in standby mode followed by the assigned shortcut key
will launch your personally designated shortcuts.
7. Press Done (left softkey).
8. If the number key you select is already assigned to
a shortcut, a prompt appears asking to replace the
existing shortcut.
Creating a Shortcut
Ⅲ Press Yes (left softkey) to replace the existing
shortcut.
When you receive your phone, all number keys may
already be assigned to shortcuts. If this is the case,
you can create new shortcuts by deleting or
replacing existing shortcuts
Note
Ⅲ Press No (right softkey) to keep the existing
shortcut and assign another number key.
Using a Shortcut
1. Go to a menu item.
For example, to create a shortcut to the screen for
creating a new Contacts entry: Press /> Contacts
and then highlight [New Contact].
To access a shortcut using the shortcut number:
1. From standby mode, press /.
83
2. On your keypad, press the number assigned to the
6. Press Done (right softkey).
shortcut.
To change the number or voice name assigned to a
shortcut:
To access a shortcut using the voice name:
1. Press and hold s.
1. Press /> Shortcuts.
2. Say the voice name you assigned to the shortcut.
The shortcut with that voice name is then
highlighted.
2. Highlight any shortcut and press Edit (left softkey).
3. With Key or Voice highlighted, press rto change
assignments.
To view a list of your shortcuts:
4. Press Done (right softkey).
ᮣ
Press /> Shortcuts.
Deleting Shortcuts
Editing a Shortcut
To delete a shortcut:
To change the order of shortcuts:
1. Press /> Shortcuts.
1. Press /> Shortcuts.
2. Highlight a shortcut and press /> Delete.
3. Press ror press Yes (left softkey) to confirm.
To delete all shortcuts:
2. With any shortcut highlighted, press /> Reorder.
3. Highlight the shortcut you are moving and press
Grab (left softkey).
1. Press /> Shortcuts.
4. Scroll to a new location and press Insert (left
softkey).
2. With any shortcut highlighted, press /> Delete All.
3. Press ror press Yes (left softkey) to confirm.
5. Repeat step 2 through step 4 for all the items you
are moving.
84
Ⅲ Any Key Ans: SelectOn to allow you to answer an
incoming call by pressing any key.
Personalize
In addition to Shortcuts, the Personalize menu gives
you other options to access menu items easily.
– or –
SelectOff to require you to press , to answer all
incoming calls.
ᮣ
Press /> Settings > Personalize, select an option,
and set your preferences.
Ⅲ Auto Ans to set your phone to automatically
answer an incoming call after a specified number
of rings when connected to a headset or
hands-free car kit.
Ⅲ Select Menu Options > Reorder Menu to change the
main menu order.
Ⅲ Select Menu Options > Add / Remove Apps to select
Java applications to add to the main menu list.
●
Off to disable Auto-Answer.
●
1 Ring, 2 Rings, 3 Rings or 4 Rings to answer calls
automatically when the phone is connected to
a hands-free car kit or a headset (sold
separately). In Auto-Answer mode, your
phone will answer calls even if you are not
present.
Ⅲ Up Key, Down Key, Left Key, Right Key, Center Key, Left
Sftkey, Right Sftkey, to set one-touch menu access
from the standby screen.
Ⅲ Power Up to set the menu item displayed when
you power on your phone. (Default Ready starts in
standby mode.)
Display Language
Call Answer Mode
You can choose to display your phone’s on screen
menus in English or Spanish.
Select how to answer incoming calls on your phone.
1. Press /> Settings > Phone Calls.
1. Press /> Settings > Display/Info > Language.
2. Select an option and press r.
2. Highlight English, Español or Automatic and press r.
85
2. Enter your phone’s six-digit security code and
pressOk (left softkey). (A disclaimer is displayed.)
Setting Prepend Dialing
The Prepend feature lets you set a prefix to be added to
the beginning of all dialed numbers, such as a country
code for international calls.
Your security code is a six-digit number used for
resetting your phone. Please contact Nextel
Customer Service if you do not know your security
code.
Note
1. Press /> Settings > Phone Calls > Prepend.
2. Select Prepend > On.
3. Read the prompt and press Yes (left softkey) to
complete the reset. (Press No [right softkey] to
cancel.)
3. Enter a prefix in the Number field (such as +1 for
international calls) and then press r.
Ⅲ To deactivate this feature, select Off during step 2
above.
Resetting All
Selecting Reset All resets phone settings and clears all
phone data, including Contacts, History, Scheduler, and
Messaging.
This setting does not apply to 911 or Sprint 411.
Note
Resetting Your Phone
1. Press /> Settings > Advanced > Reset Defaults >
Reset All.
Resetting Phone Settings
2. Enter your security code and press Ok (left softkey).
Resetting phone settings restores all the factory
defaults, including the ringer types and display settings.
The Contacts, History, Scheduler, and Messaging are
not affected.
3. Read the prompt and press Yes (left softkey) to
complete the reset. (Press No [right softkey] to
cancel.)
1. Press /> Settings > Advanced > Reset Defaults >
Reset Settings.
86
Ⅲ Ask Access — When an application attempts to
view the location of your phone, you will be
prompted to give permission. However, location
information may still be available to the phone’s
owner, fleet manager, or account administrator.
GPS Privacy Options
Your phone’s GPS privacy options control whether Java
applications or other software applications on your
phone may view the location of your phone. You may
set your phone to one of these GPS privacy options.
Setting the GPS PIN Security Feature
Privacy options do not apply to the transmission of
location information during emergency 911 calls.
Note
To prevent your GPS privacy settings from being
altered without your knowledge, your GPS privacy
option can be protected by a PIN.
To set your GPS privacy options:
1. Press /> GPS > Privacy.
When you receive your phone, the GPS security feature
is turned off, so you do not have to enter a GPS PIN to
access your GPS privacy options. If you turn this
feature on, you will be required to enter a GPS PIN to
access your GPS privacy options.
2. If your GPS PIN security feature is enabled, enter
Feature” on page 87. for more information.)
3. Select a privacy option:
To turn the GPS Enabled security feature on or off:
1. Press /> Settings > Security > GPS PIN.
2. Select On or Off.
Ⅲ Restricted — No Java or similar software
applications may view the location of your phone.
However, location information may still be
available to the phone’s owner, fleet manager, or
account administrator.
3. Enter the current GPS PIN.
Ⅲ Unrestricted — All applications may view the
location of your phone, without notifying you.
The default GPS PIN is 0000.
Tip
4. Press Ok (left softkey).
87
To change your GPS PIN:
Setting Privacy for All Java Applications
1. Press /> Settings > Security > Change Passwds >
See “GPS Privacy Options” on page 87 for instructions
on setting the privacy options for your java applications.
These options control the privacy of all Java
applications on your phone.
GPS PIN.
2. Enter the current GPS PIN and press Ok (left
softkey).
Granting or Denying Permission
3. Enter the new GPS PIN and press Ok (left softkey).
4. Reenter the new GPS PIN to confirm and then
When a java application requests access to the
location of your phone, a screen appears informing
you.
press Ok (left softkey).
Java Applications & GPS Security
To grant or deny a request:
Some Java applications can make use of your phone’s
GPS feature to determine the approximate
1. Press Grant (left softkey) or Deny (right softkey) to
grant or deny a request.
geographical location of your phone. (See “GPS
feature.) However, for privacy reasons, you may not
always want Java applications to access the location of
your phone. Your phone protects your privacy by giving
you the option to block all or some Java applications
from accessing the location of your phone.
2. Select Always to always take this action for the
application, For this session to keep this action
without notification until the phone is powered off,
or Only Once to take this action for this instance only
(you will be prompted again for subsequent
requests).
Setting Privacy for Each Java Application
1. Press /> Java Apps.
88
2. Highlight an application or suite of applications.
To access the DC/GC Options menu:
Press /> Settings> DC/GC Options.
ᮣ
If the application has requested access to the
location of your phone, this icon f appears when
you highlight the application.
Tip
ⅷ Tkgrp Silent — controls whether you hear your
Talkgroup calls.
ⅷ Tkgrp Area — lets you define your Talkgroup area.
3. Press /> Permissions.
ⅷ One Touch DC — sets One Touch Direct Connect.
4. Select privacy options for this application (you may
set them for each of the menus available under
Permissions):
ⅷ Alert Type — give the option to set alert type to ring,
vibrate or silent.
Ⅲ Always — The application always has permission
to access the phone’s location without notification.
ⅷ On/Off Settings — sets your phone’s ability to send and
receive pictures in Direct Connect calls. See “Starting
Ⅲ Ask — When the application requests access to
the phone’s location, you are prompted to grant
or deny permission (see “Granting or Denying
ⅷ Store Rcvd Info — lets you specify a prefix, such as a
country code for international calls, to be
automatically added to phone numbers you receive
in My Info from other phones, when you store the My
Info to Contacts. Select Prefix to enter the prefix to be
added. Set Add Prefix to Ask Me to set your phone to
display a prompt asking you whether to add the
prefix as you save My Info from other phones to
Contacts.
Ⅲ Never — Requests for location are denied without
notification.
DC/GC Options Menu
The DC/GC Options menu controls how your phone
handles Direct Connect calls, Group Connect calls, and
Talkgroup calls.
ⅷ PTT Backlight — controls whether or not the backlight
displays when using Direct Connect.
89
Entering the PIN
Security Settings
1. Turn on your phone.
2. When the SIM PIN screen appears, enter your
SIM PIN and press Ok (left softkey).
SIM Card Security
Except for making emergency calls, your phone
does not function without the SIM card.
Important
If you enter your PIN incorrectly three times, your
Important
SIM Card’s PIN
Changing the PIN
SIM PIN must be turned on in order to access this
You can protect access to your phone by using the SIM
card’s PIN (Personal Identification Number). When you
enable SIM PIN, you must enter the PIN each time you
power up the phone. You can change or disable the
SIM PIN.
Note
feature.
1. Press /> Settings > Security > Change Passwds >
SIM PIN.
Turning SIM PIN On and Off
2. Enter the current SIM PIN and press Ok (left
softkey).
1. Press /> Settings > Security > SIM PIN.
2. Select On or Off.
3. Enter the new SIM PIN and press Ok (left softkey).
3. Enter the current SIM PIN.
4. Reenter the new SIM PIN to confirm and then
press Ok (left softkey).
The default SIM PIN is 0000. Change your PIN to
prevent fraudulent use of the SIM Card.
Important
4. Press Ok (left softkey).
90
Unblocking the PIN
2. Select Phone Lock > Lock Now, enter the unlock
code, and press Ok (left softkey). (To set your
phone to lock the next time it is turned on, select
Auto Lock.)
If you enter your PIN incorrectly three times, your SIM
card is blocked. To unblock your SIM card, you must
contact Nextel Customer Service to get a PIN Unblock
Code (PUK). Follow their instructions for unblocking
your SIM PIN.
Unlocking Your Phone
ᮣ
At the “Enter Unlock Code” prompt, enter your
If you unsuccessfully enter the PUK code ten
times, your SIM card is permanently blocked and
must be replaced. If this happens, you get a
message to contact Nextel Customer Service.
Except for making emergency calls, your phone
does not function with a blocked SIM card.
Important
unlock code and press Ok (left softkey).
Changing the Lock Code
1. Press /> Settings > Security > Change Passwds.
2. Select Unlock Code then enter your current unlock
code and press Ok (left softkey).
Your Phone’s Lock Feature
3. Enter and reenter your new lock code, pressing
Ok (left softkey) after each.
Locking Your Phone
When your phone is locked, you can only make calls to
911. To lock and unlock your phone, you must enter
your phone’s four-digit lock code. If you do not know
your phone’s lock code, try 0000; if this does not work
contact Nextel Customer Service for assistance.
Calling in Lock Mode
You can place calls to 911 when in lock mode.
ᮣ
To call an emergency number, dial 911and
press ,.
1. Press /> Settings > Security.
91
Each entry contains the name assigned to the number
(if the phone number is in your Contacts) and the
Contacts type icon associated with the number. If the
Contacts entry containing the number has more than
one number or address stored, <> surrounds the
Contacts type icon. Duplicate calls (same number and
type of call) may only appear once on the list.
7. Recent Calls
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ The Direct Connect number Contacts type icon
appears when you receive a Direct Connect call or Call
Alert, even if the number is not stored in Contacts.
Call Alerts you have received appear as Direct Connect
calls. Like all items in the Recent Calls list, they remain
listed until you delete them or until they reach the end
of the list.
About Recent Calls
When you select a call to view its details, you see
information such as the name associated with the call,
the number, date, time, and duration of the call.
The Recent Calls list displays the last 20 numbers (or
Contacts entries) for calls you placed, accepted, or
missed, and for Call Alerts you have received. It also
displays My Info and contact information sent to you
from other phones. It is continually updated as new
numbers are added to the beginning of the list and the
oldest entries are removed from the bottom of the list.
The Recent Calls list records only calls that occur
while the phone is turned on. If a call is received
while your phone is turned off, it will not be included
in the phone’s Recent Calls list.
Note
If you return a call from the voicemail menu, it will not
be included in your phone’s Recent Calls list.
92
When you select a call to view its details, you see
information such as the name associated with the call,
the number, date, time, and duration of the call.
Calls and Call Alerts
The Recent Calls list contains the numbers of up to 20
of the most recent calls you have made and received.
My Info From Other Phones
If the number of a recent call is stored in Contacts, the
following information appears:
The Recent Calls list displays My Info sent from other
phones. See “Sending My Info and Contact
ⅷ The name assigned to the number.
ⅷ The Contacts type icon associated with the number.
This iconjappears with My Info sent from other
phones, along with the Direct Connect number of the
person who sent the information.
The Direct Connect number Contacts type icon
appears when you receive a Direct Connect call or Call
Alert, even if the number is not stored in Contacts.
When you select My Info from other phones to view its
details, you see all the information sent.
Call Alerts you have received appear as Direct Connect
calls. Like all items in the Recent Calls list, they remain
listed until you delete them or until they reach the end
of the list.
If you receive My Info from the same phone more than
once, only the most recently sent version appears in
the Recent Calls list.
For phone calls, an additional icon appears giving
information about the call.
Contact Information From Other Phones
The Recent Calls list displays contact information sent
from other phones. This information comes from the
other phone’s Contacts list or Recent Calls list. See
$
:
;
A call you made.
A call you received.
A missed call. Missed calls appear on the
Recent Calls list only if you have Caller ID.
93
This iconj appears with contact information on the
Recent Calls list.
Viewing Recent Calls
Contact information in the Recent Calls list displays:
The Recent Calls list records only calls that occur
Note
ⅷ The name contained in the contact information.
while the phone is turned on. If a call is received
while your phone is turned off, it will not be included
in the phone’s Recent Calls list.
ⅷ The Contacts type icon associated with the number
or address contained in the contact information. If the
item contains more than one number or address
stored, <> surrounds the Contacts type icon.
If you return a call from the voicemail menu, it will not
be included in your phone’s Recent Calls list.
The name or Direct Connect number of the person
who sent the contact information appears as a
separate item on the Recent Calls list, above the
information sent. If one person sends you more than
one item of contact information, all the items appear
below the person’s name or Direct Connect number.
To view the Recent Calls list:
1. Press /> Recent Calls.
2. Scroll through the list.
To view the details of an item on the list:
When you select contact information to view its details,
you see the name or Direct Connect number of the
person who sent the information and all the information
in the item.
ᮣ
From the Recent Calls list, highlight an entry and
press r.
Recent Calls Options
If you receive contact information with the same name
from the same phone more than once, only the most
recently sent version appears in the Recent Calls list.
Select a Recent Calls entry and press rto display the
date and time of the call, the phone number (if
available), and the caller’s name (if the number is
94
already in your Contacts). Press /to display the
following options:
Saving Items From Recent Calls
ⅷ Use Push To... to select Send My Info or Send Contact
(Direct Connect or Calls Alerts only).
1. From Recent Calls, highlight or select an item.
2. Press Save (left softkey).
ⅷ Send Contact to send the contact information to
another Direct Connect user.
– or –
ⅷ Update Contacts to store the number to an existing
contact.
If Save is not one of your options, press /and
then select Save or Update Contacts.
ⅷ Delete to delete the entry.
If the item you are storing is a call, Save does not
appear if the number is already stored in Contacts.
Tip
ⅷ Delete All to delete all recent calls entries.
ⅷ Add Prepend to prepend a number to the contact
3. Select [New Contact] to store the number in a new
Contacts entry, or select an entry to store the
number to an existing entry.
ⅷ Call Alert Queue to view the call alert list.
Storing My Info or contact information from another
phone to a Contacts entry that has a name assigned
to it does not change the name of the Contacts
entry.
Note
ⅷ Call Setup to configure the call.
ⅷ Call New Group to create a Group and place a Group
Connect call. (Direct Connect or Call Alerts only.
Press Create (left softkey) to begin a message to the
highlighted entry.
Tip
4. If the item is a call, you must assign a Contacts
type to the number:
You can also view the next Recent Calls entry by
pressing the navigation key right or view the previous
entry by pressing the navigation key left.
With the Contacts type field highlighted, scroll left
or right to display a Contacts type.
95
5. To add more information to the entry (optional),
follow the applicable instructions in “Creating
Prepending a Number From Recent
Calls
6. Press Save (left softkey).
If you need to make a call from the Recent Calls List
and you are outside your local area code, you can add
the appropriate prefix by prepending the number.
Deleting Items From Recent Calls
1. Select a Recent Calls entry and press />
To delete an item from the Recent Calls list:
1. From Recent Calls, highlight or select an item.
2. Press /> Delete.
Add Prepend.
2. Enter the prefix and press , to call the number.
3. Press ror press Yes (left softkey) to confirm.
To delete all items on the Recent calls list:
1. Press /> Recent Calls.
2. Press /> Delete All.
3. Press Yes (left softkey) to confirm. Press No (right
softkey) to cancel.
96
About Contacts
8. Contacts
Contacts stores up to 600 numbers or addresses. Each
Contacts entry can store several numbers or
addresses.
Information stored in Contacts is saved on your
SIM card.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ A Contacts entry contains:
ⅷ A name — A name is required if you are storing more
than one number or address to the entry; otherwise,
it is optional. Typically, this is the name of the person
whose contact information is stored in the entry.
ⅷ A ring tone — You can assign a ring tone to each
entry. This is the sound your phone makes when you
receive phone calls or call alerts from any of the
numbers stored in the entry.
ⅷ A Contacts type — Each number or address stored
must be assigned a Contacts type. (See “Types of
97
Types of Contacts
Creating Contacts Entries
Each number or address stored must be assigned a
Contacts type:
Your phone can store up to 600 Contacts entries.
Entries can store up to 10 numbers or addresses, and
an entry’s name can contain 20 characters.
Mobile
DC
phone number
Direct Connect number
phone number
phone number
phone number
email address
phone number
phone number
Talkgroup number
Group
A
0
ICE – In Case of Emergency
Tip
To make it easier for emergency personnel to identify
important contacts, you can list your local
emergency contacts under “ICE” in your phone’s
Contacts list. For example, if your mother is your
primary emergency contact, list her as “ICE–Mom” in
your Contacts list. To list more than one emergency
contact, use “ICE1–___,” “ICE2–___,” etc.
Work1
Work2
Home
Email
i
j
k
1
Fax
n
o
r
A number or address and a Contacts type are required
for all Contacts entries. Other information is optional.
You may enter the information in any order by scrolling
through the entry details.
Pager
Talkgroup
Group
Message Group
IP
)
After you have entered the number or address,
Contacts type, and any other optional information,
press Save (left softkey) to save the entry to Contacts.
Message Group List
IP address
.
7
To cancel a Contacts entry at any time press Cancel
(right softkey) and then press Yes (left softkey) to return
Other
phone number
p
98
to the Contacts list or press . to return to standby
mode.
Ⅲ When you are finished, press r.
To create a Contacts entry:
6. To assign more options to the number, including
Speed # and Voice Name, select [Options] and
proceed to steps 7-9. Otherwise, skip to step 10.
1. Press /> Contacts > [New Contact].
2. To assign a name to the entry:
Ⅲ Select Name. Enter the name and press r.
7. The default Speed Dial number assigned to a
phone number is displayed in the Speed # field.
This is always the next available Speed Dial
location. To assign the phone number to a different
Speed Dial location:
3. To assign a ring tone to the name:
Ⅲ Select Ringer and then select a ring tone.
4. To assign a Contacts type to the number or
address being stored:
Ⅲ With the Speed # field highlighted, press r.
Ⅲ Select the Contacts type field.
Ⅲ Press Delete (right softkey) to delete the current
Speed Dial number.
Ⅲ Select a Contacts type (Mobile, DC, Work1, Work2,
Home, Email, Fax, Pager, Talkgroup, Group, Message
Group, IP or Other).
Ⅲ Enter the new Speed Dial number and press r.
8. To create a voice name for a number, select Voice
Name. Follow the prompts to record a name. Speak
clearly into the microphone.
5. To store a number or address:
Ⅲ Select the # field (or ID for an email address, or IP
for an IP address).
9. When you are finished, press Back (right softkey).
Ⅲ Enter the number or address. For phone
numbers, use the ten-digit format. For Direct
Connect numbers, be sure to include the
asterisks (*).
10. To add more numbers or addresses to the entry:
Ⅲ Scroll past the information you already entered.
99
Ⅲ Enter the additional information for the entry using
steps 2–9. You must assign a name to the entry, if
you have not already.
3. Select [New Contact] to store the number to a new
entry, or select an entry to store it to an existing
entry.
11. Press Save (left softkey).
4. With the Contacts type field highlighted, scroll left
or right to select a Contacts type.
Creating Pauses and Waits
5. To add more information to the entry, follow the
applicable instructions in “Creating Contacts
When storing a number, you can program your phone
to pause or wait between digits while dialing. A pause
makes your phone pause for three seconds before
dialing further. A wait makes your phone wait for your
response before dialing further.
6. Press Save (left softkey).
Viewing Contacts
This feature is useful when using voicemail or other
automated phone systems that require you to dial a
phone number and then enter an access number.
1. Press /> Contacts and then either highlight an
entry, enter the first letter of a name, or press
Search (left softkey), and enter a name. (Your
phone finds the name you entered or the nearest
match.)
For details on using pauses and waits, (see “Phone
Storing NumbersFaster
2. If an entry has more than one number or address
stored, <> surrounds the Contacts type icon. Scroll
left or right to view the icon for each number stored
in the entry.
To store numbers to Contacts from standby mode:
1. Enter a phone number or Direct Connect number.
2. Press /> Store Number.
100
3. Press rto display the entry, and then scroll up or
3. Highlight the number type field above an open
number and press the navigation key right or left to
select a number type.
down to view all information stored for the entry.
To view more entries, continue scrolling.
Tip
4. Scroll down to the open field, enter the new
number or address and press r.
Filtering Contacts Entries
5. Press Save (left softkey) to save the new number.
You can set Contacts to display only entries containing
Direct Connect numbers, Groups, and Talkgroups.
– or –
To assign a speed dial number or Voice Name,
select [Options] > Speed # or Voice Name. Complete
the process, press Back (right softkey) and then
press Save (left softkey) to save the entry.
ᮣ
Press /> Contacts > /> Filter > Show DC. Select
Show All to display all Contacts entries.
Finding Speed Dial Numbers
ᮣ
Press /> Contacts, select an entry and select a
phone number. The speed dial number will be
listed directly under the contact phone number.
Editing Entries
1. Press /> Contacts and highlight an entry.
Adding a Number to an Entry
2. Press /> Edit.
2. Press /> Edit.
101
Deleting Entries
Assigning Speed Dial Numbers
1. Press /> Contacts and highlight an entry.
2. Press /> Delete Contact.
Your phone can store up to 600 phone numbers in
speed dial locations. (For details on how to make calls
using speed dial numbers, see “Speed Dialing” on
page 26.)
3. Press ror press Yes (left softkey) to confirm.
You can assign speed dial numbers when you add a
new Contacts entry, when you add a new phone
number to an existing entry, or when you edit an
existing number.
Deleting a Number or Address
1. Press /> Contacts and highlight an entry.
2. Scroll left or right to display the Contacts type to
delete.
To assign a speed dial number to a new phone number:
3. Press /> Delete Number.
1. Add a phone number to a new or to an existing
Contacts entry. (See “Creating Contacts Entries” on
4. Press rand Yes (left softkey) to confirm.
If an entry contains only one number or address,
deleting the number or address deletes the entry.
Note
2. Highlight [Options], press rand then select
Speed #.
3. Enter an available speed dial number and
press r.
4. Press Back (right softkey) and then press Save (left
softkey) to save the entry.
102
To assign a speed dial number to an existing phone
number:
Selecting a Ringer Type for an Entry
1. Press /> Contacts and then highlight an entry.
Assign a ringer type to a Contacts entry so you can
identify the caller by the ringer type. (See “Ring Tones”
2. Press /> Edit.
3. Select [Options] below the number, and then select
1. Press /> Contacts and then highlight an entry.
2. Press /> Edit.
Speed #.
4. Enter an available speed dial number and
press r.
3. Select Ringer and press r.
5. Press Back (right softkey) and then press Save (left
4. Scroll through available ringers. (When you
highlight a ringer type, a sample ringer will sound.)
softkey) to save the changes.
If you attempt to assign an already in-use speed dial
location to a new phone number, a message will
appear asking if you wish to overwrite the existing
speed dial assignment. Press Yes (left softkey) to
assign the location to the new phone number and
delete the previous speed dial assignment.
Note
5. Press rto select a ringer, then press Done.
103
A Datebook event contains:
ⅷ A subject — A name or number you assign to the
event.
9. Tools
ⅷ A location — The location of the event. This can also
be a phone number, Direct Connect number, or
Talkgroup.
ⅷ A start time — The start time for the event. Default is
the beginning of the day.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ⅷ A duration — The length of time the event lasts.
ⅷ A date — The date for the event. Default is the day
highlighted when the event is created.
ⅷ A repeat — For recurring events.
ⅷ A reminder — A scheduled alert for events that
include a start time.
ⅷ A ring tone for the reminder.
ⅷ A profile that your phone uses during the event.
ⅷ A Java application that starts when the event starts.
Datebook
Only subject and date are required to save an event.
Viewing Datebook
Datebook stores up to 250 events. You can store events
over a thirteen month period — twelve months after and
one month before the current date.
ᮣ
Press /> Datebook.
104
You can view Datebook by the day, by the week, or by
the month. You can also view the details of any event.
To highlight a day in month view:
Enter the date using the keypad.
To go to today’s date:
While in Datebook, press /> Go To Today.
ᮣ
ⅷ In day view, brief information about each event for
that day appears.
ⅷ In week view, events appear as markers
ᮣ
corresponding to their times.
To go to any date in Datebook:
1. While in Datebook, press /> Go To Date.
2. Select a date.
ⅷ In month view, days with events are marked.
To view an event:
1. Select the day the event occurs.
2. Select the event.
Creating Events
Every Datebook event must have a subject and be
stored to a date. Other information is optional.
To change the current view:
ᮣ
While in Datebook, press /and select a view.
After you have entered the information, press Done (left
softkey) to store the event to Datebook.
Day view is the default setting.
Note
To create a Datebook event:
Navigating Datebook
1. While in datebook, press New (left softkey).
– or –
To scroll through Datebook:
ᮣ
Scroll left and right using the navigation key.
To see more in day view:
Scroll up and down using the navigation key.
In day view, select [New Event].
2. To assign a subject to the event, select Subject and:
ᮣ
105
Ⅲ Enter the name or enter a phone number, Direct
Connect number, or Talkgroup number.
7. To make the event a recurring event:
Ⅲ Select Repeat and then select a repeat cycle.
– or –
● If the event occurs more than once a week,
select Multiple Day, and select the days.
Press Browse (left softkey) to choose from
common event names.
● Press Done (left softkey).
3. To assign a location to the event (optional), select
Location and enter the location or enter a phone
number, Direct Connect number, or Talkgroup
number.
Ⅲ In the End field, select a date for the event to stop
recurring.
8. To create a reminder for this event, select Reminder
and then select a reminder time or select Custom to
enter a reminder time.
4. The start time automatically assigned to an event is
the beginning of the day. To change the start time
or assign no start time, select Start and then enter a
start time or press No Time (left softkey).
If an event has no start time, you cannot create a
reminder for it.
Note
9. To set the ring tone for a reminder, select Ring Tone
5. To assign a duration, select Duration and select a
duration from the list or select Custom and enter a
duration.
and then select a ring tone.
10. To assign a profile for your phone to use during
the event, select Profile and then select a profile.
(Your phone switches to this profile when the event
starts and switches back to the previous profile
when the event ends.)
6. The date automatically assigned to an event is the
date that was highlighted or selected when you
began creating the event. To change the date of
the event, select Date and then enter a date.
11. To assign a Java application to start when the
event starts, select App and then select an
106
application. (If you created a reminder for this
event, your phone prompts you to start the Java
application when you get the reminder.)
5. To change more information, follow the applicable
edit the event.
12. Once you have entered all relevant information and
6. Press Done (left softkey) to store the event.
settings, press Done (left softkey).
Deleting Events
To cancel without saving:
1. Select the day the event occurs.
ᮣ
Press Cancel (right softkey).
2. Select the event and press /> Delete.
Editing Events
3. If the event is not a recurring event, press ror
press Yes (left softkey) to confirm.
To change the details of an event:
– or –
1. Select the day the event occurs.
2. Select the event and press Edit (left softkey).
If the event is a recurring event, select This Event
Only to delete only the event selected in step 2, or
select Repeat Event to delete all occurrences of the
event.
Events” on page 105 to edit the event.
To copy an event to another date:
Receiving Reminders
1. Select the day the event occurs.
2. Select the event and press /> Copy.
3. Press Yes (left softkey) to confirm.
4. Enter a date and press r.
If you created a reminder for a Datebook event, when
the reminder time occurs, your phone notifies you with
text on the display and a reminder tone.
107
To view more details about the event:
Press View (left softkey).
To dismiss the reminder:
Press Dismiss (right softkey).
Making Calls From Datebook
ᮣ
To make a phone call:
1. Highlight or select an event containing a phone
number.
ᮣ
2. Press , or press /> Call # in Event.
For Events With Java Applications
To make a Direct Connect call or Talkgroup call:
If you assigned a Java application to start when the
event starts, you can start the application when you get
the reminder.
1. Highlight or select an event containing a Direct
Connect or Talk Group number.
2. Press the DC button. (If you did not include a #
before a Talkgroup, press /> Talkgroup, and then
press the DC button.)
ᮣ
Press /> Launch.
Making Calls From Datebook and
Datebook Reminders
To send a Call Alert:
1. Highlight or select an event containing a Direct
If you stored a phone number, Direct Connect number,
or Talkgroup number in the Subject or Location field of a
Datebook event, you can call or send a Call Alert to that
number from Datebook or from the reminder.
Connect number.
2. Press /> Alert # in Event, and then press the DC
button.
If you store the same type of number (phone number
or DC/Talkgroup number) in both fields, the number in
Subject takes precedence.
Making Calls From Datebook Reminders
To call a number:
ᮣ
Press , or press /and then select Call # in Event.
108
To make Direct Connect calls or Talkgroup calls:
Press the DC button.
To send a Call Alert:
Connect, Group ID (Talkgroup number), Carrier IP,
IP1 Address and IP2 Address.
ᮣ
If you request equipment-related transactions on
your account, Nextel Customer Service may require
you to provide specific information about your
phone. Press /while in My Info to display a
submenu that includes your phone's service status,
unit information, and phone identification numbers
including IMEI, SIM ID, and Serial Number (SN).
Note
ᮣ
Press /> Alert # in Event, and then press the DC
button.
Customizing Datebook Setup
1. Select /> Datebook > /> Setup.
Adding a Name to My Info
2. Select an option and adjust the values.
Ⅲ Options include Start View, Daily Begin, Delete After,
Time Shift, Alert Timeout and Clock.
1. Press /> My Info.
2. Press Edit (left softkey) > Name.
3. Enter a name and press r.
My Info
You can also edit the information in Line 1 and Line 2,
but your changes are only temporary. The next time
your phone registers on the network, your actual phone
numbers appear again in My Info.
My Info lets you view your phone number, Direct
Connect number, and other phone information.
ᮣ
Press /> My Info.
You may need to select More to display My Info.
Note
Ⅲ Information displayed includes My Name (optional,
you may enter it yourself), Line 1 Line 2, Direct
109
Suspending Applications
Java Applications
When you suspend an application, it does not stop
running. It goes to the background so that you can run
another application in the foreground.
Installing Applications
1. Press /> Java Apps.
To suspend an application:
2. Select an application or suite of applications.
Messages appear as the application installs.
ᮣ
Press ..
To view your suspended applications:
Press /> Java Apps > Suspended Apps.
3. Press Done (left softkey).
Running Applications
1. Press /> Java Apps.
ᮣ
You can have up to three applications running at one
time — one running in the foreground and two in the
background.
2. Select an application or suite of applications. If you
have selected a suite of applications, select an
application.
Resuming Applications
You can resume a suspended application at any time.
This brings it to the foreground.
If you do not hear the sounds associated with the
Java application, select Settings > Volume and
check the volumes of Speaker and Earpiece.
Tip
To resume a suspended application:
1. Press /> Java Apps > Suspended Apps.
2. Select an application to resume.
110
To access a catalog of items available for purchase and
download:
Ending Applications
To end an application:
ᮣ
Press /> Java Apps > Download Appsor
ᮣ
Press the appropriate softkey to end or exit the
press /> Downloads.
application or press /> End.
account to find a wide selection of available Java
applications and downloading instructions.
To end an application Java Apps > Suspended Apps.
3. Highlight an application and press End (left
softkey).
Deleting Applications
To end all applications:
To delete an application:
1. Press /> Java Apps > Suspended Apps >
/> End All.
1. Press /> Java Apps.
2. Highlight an application and press /> Deinstall.
3. Press ror Yes (left softkey) to confirm.
2. Press ror press Yes (left softkey) to confirm.
3. To end all applications without letting them exit,
press EndNow (left softkey) and then press Finish
(right softkey).
4. When your phone has finished deleting the
application, press Done (left softkey).
To delete all Java applications:
Downloading Applications
1. Press /> Java Apps.
To run more Java applications, you can download
them into your phone.
2. Highlight Java System and press /> Delete All.
(You may need to press More [left softkey] to
displayJava System.)
111
3. Press ror press Yes (left softkey) to confirm
ⅷ For time-based items, either the date and time the
item expires, or the number of days left.
ⅷ For count-based items, the number of credits (uses)
left or an unlimited use notice.
Digital Rights Management (DRM)
ⅷ The name of the item’s vendor.
When you download multimedia content available
online, such as Java applications, these items may be
subject to DRM restrictions. DRM, or digital rights
management, is a system that defines how copyrighted
multimedia content can be distributed and used.
To view the license of a DRM item:
1. Go to the location that contains the item.
2. Highlight the item and press /> License Info.
DRM limits items to time-based or count-based usage
settings. Time-based settings let you use the given item
for a specified interval. Count-based settings let you
use an item for a specified number of times after you
download it or for unlimited use.
Renewing DRM Licenses
Java application data is stored in your phone using
the same memory space used to store messages,
voice records, pictures, ring tones, and wallpaper
images. Deleting some of these other items frees
memory for Java applications.
Note
Managing Items
Depending on how the third-party vendor has set rights
for the given DRM item, you may be unable to perform
some of the following tasks.
1. Go to the location on your phone that contains the
item.
2. Highlight a DRM item and press Renew (left
softkey) or press /> Renew.
Viewing License Information
You can check a DRM item’s license to view the
following information:
112
3. Select the link to the page where you purchased
the item and then follow the vendor’s instructions
for purchasing an additional license.
GPS Enabled
Your phone’s GPS Enabled feature uses information
from Global Positioning System (GPS) satellites orbiting
the Earth to determine the approximate geographical
location of your phone. The availability and accuracy of
this location information (and the amount of time that it
takes to calculate it) will vary depending on the
Deleting Items
If you delete a DRM item that you purchased from
Nextel from your phone, you will have to purchase it
again to download it.
environment in which you are using the GPS feature.
You cannot delete items that are DRM locked.
Note
When you make a 911 emergency call, the GPS feature
of your phone can help emergency personnel locate
you if your phone has adequate access to GPS satellite
signals and your emergency response center is
equipped to process such information.
Under certain conditions, third-party vendors will let
you download an item multiple times within a given
time frame, even if you deleted the item. Please
contact the third-party vendor of an item to learn
more about the vendor’s download regulations.
You can also use the GPS feature to view your
approximate location. Location information appears on
the phone’s display.
1. Highlight a DRM item and press /> Delete.
2. If prompted, press Yes (left softkey).
Java applications loaded on your phone can also
request your location. If your phone is connected to a
laptop computer or similar device, software running on
that device can request your location. To protect your
privacy, you can control whether these requests are
About Expired Items
Most items will continue to display on your phone until
you delete them. You can also choose to renew the
license for an expired item.
113
determine the approximate location. This time will
increase where there is reduced access to satellite
signals. When your approximate location is
determined, it is made available to the appropriate
emergency response center.
IMPORTANT: Things to Keep in Mind
If you are using the GPS feature of your phone while
driving, please give full attention to driving and to the
road.
Where adequate signals from multiple satellites are not
available (usually because your GPS antenna cannot
establish a view of a wide area of open sky, such as in
underground locations, inside or between buildings, or
in dense tree cover), the GPS feature of your phone
WILL NOT WORK.
In some cases, your local 911 emergency response
center may not be equipped to receive GPS location
information. For this reason, and because the GPS
location information reported is only approximate or
may not be available in your location, always report
your location to the 911 operator you speak to when
making an emergency call, if able, just as you would
when using a phone without GPS capabilities.
Walking or driving very slowly may also substantially
reduce GPS performance.
If you are concerned about whether your local 911
emergency response center is equipped to receive
GPS location information, contact your local
authorities.
Note
Making an Emergency Call
ᮣ
Dial 911 and press , to be connected to an
emergency response center. If you are on an active
call, you must end it before calling 911.
Viewing Your Approximate Location
When you make an emergency 911 call, the GPS
feature of your phone begins to calculate your
approximate location. Even where your phone has
good access to sufficient GPS satellite signals and
network assist data, it may take 30 seconds or more to
ᮣ
Press /> GPS > Position.
This displays the following information about the last
time your location was calculated:
114
ⅷ The time (as Greenwich Mean Time) and date that
the location was last calculated.
Enhancing GPS Performance
Sometimes the GPS feature of your phone may be
unable to complete a location calculation successfully.
ⅷ The approximate location, expressed as latitude and
longitude.
To improve accuracy and increase your chances of a
successful calculation, do the following while your
phone is determining your approximate location:
ⅷ The estimated accuracy of the calculated location.
ⅷ The number of satellites used to calculate the
location. In general, more satellites make for better
accuracy.
ⅷ Stay in the open. The GPS feature works best where
there is nothing between your phone and a large
amount of open sky. If possible, go outside, away
from tall buildings and foliage.
To calculate your location again:
ᮣ
Press Rfrsh (left softkey).
ⅷ Hold your phone to enhance reception. Signals from GPS
satellites are transmitted to your GPS antenna, which
is in your phone antenna. Hold your phone away
from your body, giving the antenna clear access to
satellite signals. Do not cover the antenna area with
your fingers or anything else.
It may take your phone several minutes to complete the
process of determining your location, during which the
phone displays “Scanning For Satellites.”
The Position screen displays the updated information.
To cancel a location calculation before it is completed:
ⅷ Stand still. If possible, stand still until your phone is
finished determining your location. Moving your
phone at a walking pace while your phone is
calculating your approximate location may
substantially decrease GPS performance.
ᮣ
Press Cancel (right softkey) to return to the Position
screen or press . to return to standby mode.
Each time approximate location of your phone is
calculated, the latest location information is stored in
your phone. You will see this information the next time
you view the Position screen.
ⅷ In a car. When using the GPS Enabled feature in a car,
position your phone so that the GPS antenna has
115
good access to GPS signals through the car’s
windows. Typically, the GPS antenna has best access
to GPS signals in a car when placed near a window.
running the map software, which displays your location
on a map. Your phone provides an updated location
every second and the map software displays your
changing location on its map.
Although moving your phone at a walking pace
decreases GPS performance, moving it at the speed
of a moving car does not.
Note
more details on obtaining good location information.
Because your phone is continuously determining
ⅷ Stay in network coverage. The network will provide your
phone with information that helps determine your
location more quickly and accurately.
Note
your location, using the GPS feature of your phone
with map software uses the phone’s battery power
quickly.
Using GPS With Map Software
To connect your phone to your laptop or other device:
You can use the GPS feature of your phone to provide
approximate location data to a laptop computer or
similar device that is running interactive map software
such as that made by DeLorme or Microsoft. This way,
if your phone has good access to GPS signals, your
approximate position on a map can be made available
as you travel in a vehicle.
1. Pull open the connector cover.
2. With the phone’s display facing up, insert a
micro-USB data cable into the charger connector.
To do this, connect your phone to your laptop (or other
device) with a data cable and set your phone to
transmit data (see “To connect your phone to your
provides your approximate location to the device
116
3. Insert the data plug into the COM port of your
Each time you power your phone on, NMEA OUT is
automatically set to Off.
laptop or other device.
Make sure no other application is using the COM port
selected.
Memo Feature
Make sure the COM port settings of your laptop or
other device are set to the following:
Memo lets you store a number, make a call to that
number, and save it to Contacts.
ⅷ Bits per second: 4800
ⅷ Data bits: 8
To create a memo:
ⅷ Parity: None
1. Press /> Memo.
ⅷ Stop bits: 1
2. Enter a number and press r.
To view the memo later:
ⅷ Flow control: Hardware
To set your phone to send location information to your
laptop or other device:
ᮣ
Press /> Memo.
To delete the memo:
1. Press /> GPS > Interface.
1. Press /> Memo.
2. Set NMEA OUT to ON.
2. Press and hold Delete (left softkey) and then
Your phone is now sending location data to your
laptop or other device.
press r.
To edit the memo:
To stop sending location data to your laptop or other device:
1. Press /> Memo.
ᮣ
Set NMEA OUT to Off.
117
2. Press and hold Delete (left softkey) to delete the
number.
6. Press Save (left softkey).
Voice Records
3. Enter the new number and press r.
To make a call to the memo number:
1. Press /> Memo.
A voice record is a recording you make with your
phone and can play back. You can record notes to
yourself or phone calls.
2. To make a phone call, press ,. To make a Direct
Connect call, press the DC button.
Your phone can store up to 20 voice records.
To store the memo number to Contacts:
1. Press /> Memo.
Creating Voice Records
1. Press /> VoiceRecord > [New VoiceRec].
2. Recite a message into the microphone.
3. When you are finished recording, press r.
To record a phone call:
2. Press /> Store to Cntcs.
3. To store the number as a new entry, select
[New Contact].
– or –
To store the number to an existing entry, select the
entry.
1. While on an active call, press /> Record.
2. When you are finished recording, press r.
4. With the Contacts type field highlighted, scroll left
or right to display a Contacts type for the number.
Recording of phone calls is subject to applicable
laws regarding privacy and recording of phone
conversations.
Note
5. To add more information to the entry, follow the
applicable instructions in “Creating Contacts
118
3. Press ror Yes (left softkey) to confirm.
To delete all unlocked voice records:
Playing Voice Records
1. Press /> VoiceRecord.
1. Press /> VoiceRecord.
2. Highlight a voice record and press r.
3. To stop the voice record while it is playing,
2. Highlight a record and press /> Delete All.
3. Press ror Yes (left softkey) to confirm.
press r.
To fast forward, scroll right. To rewind, scroll left. To
pause or resume, press any number key.
Tip
Locking Voice Records
When you lock a voice record, it cannot be deleted
until you unlock it.
Labeling Voice Records
When you create a voice record, it is labeled with the
time and date it was recorded. You can rename it with
a custom label.
1. Press /> VoiceRecord.
2. Highlight a record and press /> Lock to lock it.
Press /> UnLock to unlock a message.
1. Press /> VoiceRecord.
When a voice record is locked, this icon Xappears
next to it.
2. Highlight a record and press Label (left softkey).
3. Enter a label and press r.
Managing Memory
Deleting Voice Records
To view the amount of memory available for voice records:
To delete an unlocked voice record:
1. Press /> VoiceRecord.
1. Press /> VoiceRecord.
2. With [New VoiceRec] highlighted, press Memory (left
softkey).
2. Highlight a record and press /> Delete.
119
ⅷ To reset the timer, press r then Reset (left softkey).
Press ror press Yes (left softkey) to confirm.
Call Timers
Call timers measure the duration of your phone calls,
Direct Connect, or Group Connect calls, and the
number of kilobytes sent and received by your phone:
Media Center
The Media Center lets you access pictures, musical
ringtones and voice recordings stored in your phone’s
memory.
ⅷ Last Call — displays the duration of your most recent
phone call.
ⅷ Phone Reset — keeps a running total of your phone
call minutes, until you reset it.
All pictures stored in your phone’s memory can be
accessed through the Media Center:
ⅷ Phone Lifetime — displays the total minutes of all your
phone calls.
ⅷ DC/GC Reset — keeps a running total of all of your
Direct Connect and Group Connect call minutes,
until you reset it
ⅷ DC/GC Lifetime — displays the total minutes of all your
Direct Connect and Group Connect calls.
ⅷ Voice records created when your phone was not in a
call.
ⅷ Musical ringtones in the list of ringtones.
ⅷ Audio files saved from MMS messages you received.
ⅷ Audio files (songs, recordings) you downloaded to
your phone.
ⅷ Kbytes Reset — keeps a running total of the number of
kilobytes sent and received by your phone, until you
reset it.
Pictures and audio files accessible through the Media
Center can be sent in MMS messages.
Multimedia message size limits apply when attaching
items from the Media Center. See “Creating and
To view or reset a timer:
1. Press /> Call Timers.
2. Select a timer and press r.
120
ᮣ
To filter by media type scroll left or right.
Viewing the Media Center
Keeping the Last Filter Setting
1. Press /> Media Center.
2. Scroll to view the items in the Media Center.
You can set the Media Center to show all items every
time you access it or to keep the filtering setting you
had when you last viewed it.
Choosing Thumbnail View or List View
You can set the Media Center to show a thumbnail of
each picture as you view the list of items or show the
list of items without thumbnails.
1. Press /> Media Center > /> Setup >
Remember Filter.
2. Select On to keep the filtering setting you had
when you last viewed the Media Center.
1. Press /> Media Center > /> Set View.
2. Select Thumbnail View or Plain List View.
When you receive your phone, the Media Center is set
to show all items every time you access it.
Filtering by Media Type
Accessing Items Listed
You can set the Media Center to show all types of
media items, only pictures, or only audio recordings.
1. Press /> Media Center.
ⅷ Media: All — all items accessible through the Media
Center.
2. Scroll down to highlight an item and press rto
select it.
ⅷ Media: Pictures — all pictures.
3. Scroll right or left to access additional items.
ⅷ Media: Audio — all audio files accessible through the
Media Center.
ⅷ Media: Video — all video files accessible through the
Media Center.
121
When an item is locked, it cannot be deleted from the
Media Center. See “Locking Items” on page 125.
Locking an item has no effect on its forward locking.
Sorting by Time or Name
You can set the Media Center to sort items by the time
the item was created or by the name of the item.
DRM Items
1. Press /> Media Center > /> Setup > Sort.
Except for Java applications, which download to Java
Apps, the default location for any DRM items that you
download is the Media Center.
2. Select By Time or By Name.
When you receive your phone, the Media Center is set
to sort items by time.
Depending on how a given third-party vendor has set
rights for an item, the item may include the following
status icons.
Forward Locked Items
Some items saved to the Media Center from MMS
messages or by downloading may be forward locked.
Forward locked items are usually copyright protected,
and you cannot share them with anyone.
The item is a DRM item.
c
e
The DRM item has expired.
You cannot remove forward locking from an item.
All DRM items are forward locked. As with other items
in the Media Center, you can lock DRM items. (See
When you view items in the Media Center, one of these
icons appears next to each forward locked item:
Pictures
Forward locked.
O
The Media Center lets you view pictures and send
pictures that are not forward-locked in MMS messages,
Direct Connect calls, or with Bluetooth. You can assign
Forward lock and locked.
]
122
them to Contacts entries or set them as your phone’s
wallpaper.
Sending Messages” on page 49.) The picture is
automatically included as an attachment.
Viewing Pictures
Sending With Bluetooth
To view a picture, select it from the list of items in the
Media Center.
You must set up your phone to send items with
Bluetooth before sending a picture. (See “Sending
If your phone is set to show thumbnails, a thumbnail of
each picture appears next to the picture in the list of
items. If your phone is not set to show thumbnails, this
icon g appears next to the picture.
1. Scroll to or select a picture.
2. Press /> Send Via > Bluetooth.
To see a larger or smaller view of the picture you are
viewing:
3. Select the device you want to transfer to or search
for the device you want to transfer to by selecting
[Find Devices].
1. Press /> and then select Zoom.
2. Select the zoom option you want.
4. If prompted, bond with the device. (Your phone
connects to the device and transfers the picture.)
If the picture does not fit in the display, scroll left and
right and up and down to view different parts of the
picture.
Setting as Wallpaper
1. Scroll to or select a picture.
2. Press /and then select Set As Wallpaper.
Sending a Message
1. Scroll to or select a picture and then press Send
(left softkey).
123
Playing a Recorded Video
Audio Files
1. Press /> Media Center.
The Media Center lets you play audio files (songs,
recordings, podcasts), send them in MMS messages,
and assign them to Contacts entries.
2. Select the video you wish to play and press r.
3. To stop the video press the down navigation key.
To play the video again, press r.
Playing Audio Files
ᮣ
To play an audio file, select it from the list of items
in the Media Center.
Sending in a Message
1. Scroll to or select an audio file and press Send (left
softkey).
This icon a appears next to each audio file in the list of
items.
2. Create and send the message.The audio file you
selected is automatically included as an
attachment.
When viewing the list of items in the Media Center,
you can scroll left or right, or press *or #, to
change the type of media that is displayed in the list.
Tip
Renaming Items
Ⅲ To stop the file before it has finished playing,
press ror scroll down.
1. Press /> Media Center.
Ⅲ To restart the audio file, press r.
2. Scroll to or select an item.
3. Press /and then select Rename.
Ⅲ To to fast forward, scroll right. To rewind, scroll left.
The longer you hold the scroll key, the faster the
voice recording fast forwards or rewinds.
4. Delete the item’s name, enter a new name, and
press r.
Ⅲ When you play an audio file, an animated image
appears on the display.
124
within a given time frame. Please contact the DRM
vendor to learn more about their download regulations.
Locking Items
When you lock an item in the Media Center, it cannot
be deleted until you unlock it.
1. Press /> Media Center.
2. Scroll to or select an item.
3. Press /and then select Lock or Unlock to lock or
unlock the item.
When you view items in the Media Center, one of these
icons appears next to each locked item:
Locked.
O
Forward lock and locked.
]
Deleting Items
Deleting items from the Media Center means they can
no longer be accessed anywhere in your phone,
including the list of ringtones, the list of voice records,
and Contacts.
Under certain conditions, some DRM vendors will not
charge you if you download an item multiple times
125
Deleting an Item
Managing Memory
1. Press /> Media Center.
2. Scroll to or select an item.
3. Press /and then select Delete.
4. Press Yes (left softkey) to confirm.
To view your used memory, free memory, and memory
capacity of your phone:
1. Press /> Media Center.
2. Scroll to or select any item in the Media Center.
3. Press /and then select Memory Usage.
To free memory, delete items.
Deleting All Items
You can delete all unlocked items currently in view,
depending on how Media Center filtering is set. See
to show all types of Media Center items, all unlocked
items are deleted.
Items accessible through the Media Center that are
stored in your phone’s memory use the same
memory space used to store messages, Java
application data, and voice records created when
your phone is in a call. Deleting some of these other
items frees memory.
Tip
1. Press /> Media Center.
2. Press /and then selectDelete All.
3. Press Yes (left softkey) to confirm.
126
2. Using the display screen as a viewfinder, aim the
camera lens at your subject.
10. Camera
3. Press Capture (left softkey), ror euntil the
shutter sounds.
Ⅲ Press Send (left softkey) to send the picture in an
MMS message, Discard (right softkey) to discard
the picture and return to the camera, rto save
the picture and return to camera, or press /for
the following options:
ࡗ ࡗ ࡗ ࡗ ●
Send Picture vi... to send pictures to recent call
or contact.
●
Send Via... to send the picture via Bluetooth,
Direct Send (PTT), or MMS (multimedia
messaging).
Taking Pictures
●
●
Save [OK] to save the picture.
Taking pictures with your phone’s built-in camera is as
simple as choosing a subject, pointing the lens, and
pressing a button.
Set As Wallpaper to use the picture as your
phone’s wallpaper.
●
●
Media Center to save the picture to the Media
Center and open the Media Center.
1. Press /> Camera to activate camera mode.
To activate camera mode, you can also press
the camera key (e) on the right side of the
Shortcut
Memory Usage to see the amount of used and
available memory on your phone.
127
●
Camera Setup to set the camera default settings
for Ask for Name, Shutter Sound, Default Size and
Default Quality.
ⅷ Camera Setup to set the camera default settings.
Setting the Self Timer
1. From camera mode, press /> Self Timer.
Camera Options
2. Highlight a delay length (10 seconds, 15 seconds or
20 seconds) and press r.
With the phone in camera mode, press /to display
additional camera options:
3. Press Capture (left softkey), r, or ewhen you are
ready to start the timer. (The lower portion of the
display screen displays the countdown time.)
ⅷ Media Center to go to the Media Center to review your
saved pictures.
4. Get ready. The camera will automatically capture
the picture when the timer runs down.
ⅷ Record Video to switch to video mode. (See
To cancel the self-timer after it has started:
Zoom” on page 128 for details.)
ᮣ
Press Cancel (right softkey).
ⅷ Lighting adjust the camera to your lighting
environment. Select Normal or Low Light.
Using the Zoom
Depending on your resolution settings, you can adjust
the zoom from 1x to 4x.
the Self Timer” on page 128 for details.)
ⅷ Picture Quality to select the picture quality between
Normal or Fine
To adjust the zoom:
1. While in camera mode, press /> Zoom.
2. Select from 1X, 2X or 4X.
ⅷ Picture Size to select the picture size.
ⅷ Memory Usage to verify memory usage.
128
information.)
Camera Setup
Set your camera’s resolution and default size in the
Camera Setup menu.
Press e > / > Record Video.
Shortcut
1. Press /> Camera > /> Camera Setup.
2. Using the display screen as a viewfinder, aim the
lens at your subject.
2. Select an option and press r.
Ⅲ Ask for Name: Select On for the camera to prompt
you to enter a new File Name when saving a
picture.
3. Press Recrd (left softkey), e, or rto begin
recording.
4. Press e, ror Stop (left softkey) to stop recording.
(The video will automatically be saved in your
phone.)
Ⅲ Shutter Sound: Select an option and press r.
Ⅲ Default Size: Select a size and press r.
Ⅲ To return to camcorder mode to take another
video, press e.
Ⅲ Default Quality: Highlight Normal orFine and
press r.
5. Press /for more options:
Ⅲ Review to play back the video.
Ⅲ Save [OK] to save the video.
Recording Videos
In addition to taking pictures, you can also record, view,
and send videos with the phone’s video camera.
Ⅲ Media Center to go to the Media Center to review
your saved videos.
Ⅲ Send Via... to send the video via Bluetooth or MMS
To record a video:
message.
1. Press /> Camera > /> Record Video to activate
video mode. (Additional video options are
Ⅲ Memory Usage to verify memory usage.
available through the video mode Options menu.
Ⅲ Camera Setup to set the camera default settings.
129
Video Mode Options
Storing Pictures and Videos
With the phone in video mode, press /to display
The Media Center allows you access pictures, video
and audio recordings stored on your phone’s memory.
additional camera options:
ⅷ Media Center to go to the Media Center to review your
saved videos.
Phone Options
ⅷ Capture Picture to switch to picture mode.
When you are highlighting a picture, audio or video file
stored in the phone, press /to display the following
options:
ⅷ Delete to delete the selected file.
ⅷ Lock to lock the selected file.
ⅷ Rename to rename the selected file.
ⅷ Send Via... to send the file via Bluetooth, Direct
ⅷ Zoom to zoom in on a subject.
ⅷ Lighting adjust the camera to your lighting
environment. Select Normal or Low Light.
ⅷ Video Length to select the video length.
ⅷ Memory Usage to verify memory usage.
ⅷ Camera Setup to set the camera default settings.
Send(PTT) or MMS message.
ⅷ Camera to activate Camera mode.
Selecting Video Settings
1. From video mode, press /> Camera Setup.
ⅷ Set As Wallpaper to display the currently highlighted
picture as a wallpaper.
2. Select an option and press r:
ⅷ Send Picture vi... to send a picture to a recent call or
contact.
Ⅲ Ask for Name: Select On for the camera to prompt
you to enter a new File Name when saving a
video file.
ⅷ Delete All to delete all files in the folder.
ⅷ Filter to select the media type to view from Media: All,
Media: Pictures, Media: Audio, Media: Video.
Ⅲ Shutter Sound: Select an option and press r.
130
ⅷ Set View to switch the display from Plain List View to
Thumbnail List View.
ⅷ File Size to display the size of the file.
ⅷ Memory Usage to verify available memory.
ⅷ Setup to Sort files (By Time or By Name), and to turn
Remember Filter on or off.
131
To turn Bluetooth on:
1. Press /> Bluetooth > Setup > Power.
2. Select On and press rto enable Bluetooth.
To turn Bluetooth off:
11. Bluetooth
1. Press /> Bluetooth > Setup > Power.
2. Select Off and press rto disable Bluetooth.
To turn discoverable mode on:
ࡗ ࡗ ࡗ ࡗ ᮣ
Press /> Bluetooth > Find Me.
For the duration selected under Find Me Time, the
phone will be discoverable by other devices that
are within range.
Turning Bluetooth On and Off
Bluetooth Status Indicators and LED
Bluetooth is a short-range communications technology
that allows you to connect wirelessly to a number of
Bluetooth devices, such as headsets and hands-free
car kits, and Bluetooth-enabled handhelds, computers,
printers, and wireless phones. The Bluetooth
The Bluetooth status indicators on your phone’s display
Bluetooth connection status at a glance:
communication range is usually up to approximately
30 feet. By default, your device’s Bluetooth feature is
turned off. Turning Bluetooth on makes your phone
“discoverable” by other in-range Bluetooth devices.
No LED or Status Indicator – Bluetooth is disabled (default
status)
B – Status indicator will blink and LED will be solid
when the phone is in discovery mode.
132
B – Status indicator will be solid and LED will blink
when connected to a Bluetooth device.
Connecting Bluetooth Devices
Pairing and Connecting
Bluetooth Menu
1. Press /> Bluetooth > Hands Free >
[Find Devices] to connect to a hands-free device.
The Bluetooth menu allows you to set up many of the
characteristics of your phone’s Bluetooth service.
– or –
1. Press /> Bluetooth.
Press /> Bluetooth > Link to Devices to pair with a
device. (Your phone will display a list of discovered
in-range Bluetooth devices.)
2. Set your Bluetooth options.
Ⅲ Select Hands Free to discover and connect to
2. Highlight a device and press r.
hands-free devices.
Ⅲ Select Link to Devices to scan for and connect your
phone to an available Bluetooth device.
3. Follow the prompts, including entering a PIN if
requested, and press rto complete the
connection.
Ⅲ Select Device History to link to devices that have
been connected to your phone.
Pairing uses a PIN to establish a trusted connection
between your phone and another Bluetooth device.
This connection is stored for future connections.
Ⅲ Select Setup to turn Bluetooth on and off, rename
your phone for Bluetooth, and set the time for the
Find Me command listed below.
Due to different specifications and features of other
Bluetooth-compatible devices, display and
operations may be different, and functions such as
transfer or exchange may not be possible with all
Bluetooth-compatible devices.
Note
Ⅲ Select Find Me to make your phone discoverable
to Bluetooth devices for a period of time.
133
Connecting to a Stored Device
Disconnecting From a Device
If you have previously connected to a device, the
device will be stored on your phone so you can
connect with it easily.
1. Press /> Bluetooth > Link to Devices.
2. Press Drop (left softkey) and then press Yes (left
softkey).
1. Press /> Bluetooth > Link to Devices and then
select a device.
Pressing No (right softkey) when prompted exits the
menu without disconnecting the device.
Note
2. If prompted to bond with the device, press Yes (left
softkey).
Understanding Bluetooth Access Settings
3. If prompted, enter the Bluetooth PIN and press Ok
A Bluetooth device can have either Automatic or Ask
security access. The first time a Bluetooth device
connects to your MotorolaClutch i465 phone, you must
grant the device permission to connect. You can then
change the access setting of the device to either
Automatic or Ask.
(left softkey). Your phone will connect to the device.
Using Bluetooth During a Call
During a call, you can connect with available Bluetooth
devices.
If you set a device to Automatic, that device can connect
automatically to your phone when it is in range. If you
set a device to Ask, that device must request
If the Hands Free menu contains only one device,
then your phone will automatically try to connect to
that device.
Note
permission before it can connect to your phone.
To use Bluetooth during a call:
1. While in a call, press /> Use Bluetooth.
2. Select a device.
Devices are automatically granted permission during
the ten seconds after connecting.
134
The default for hands-free devices, such as Bluetooth
headsets, is Automatic.
Sending Items via Bluetooth
Setting Device Details
Sending Contacts, Datebook Events and
Media Center Items
The device history stores a list of up to 20 devices that
have connected with your phone.
Bluetooth lets you send Contacts entries, Datebook
events, and compatible Media Center items to
connected devices.
ᮣ
Press /> Bluetooth > Device History.
From the device history, highlight a device and press
Edit (left softkey) to edit the device name and change
the access settings. To delete a device, highlight it,
press / > Delete, and then press Yes (left softkey).
Files sent or received may be up to1 MB.
You can only connect your phone to one device at a
time.
If you delete a device from device history, you will
have to find the device to connect with it. (See
Note
a list of MotorolaClutch i465 phone Bluetooth
compatible devices.
Note
Sending Contacts
1. Press /> Contacts.
2. Highlight a contact and press /> Send Via... >
Bluetooth.
3. Select a device or search for a device by selecting
[Find Devices].
135
4. If prompted, bond with the device. Your phone
connects to the device and transfers the contact.
2. Highlight a file and press /> Send Via... >
Bluetooth.
3. Select a device or search for a device by selecting
Sending Datebook Events
[Find Devices].
1. Press /> Datebook.
4. If prompted, bond with the device. Your phone
connects to the device and transfers the file.
2. Highlight an event and press /> Send Via....
Ⅲ For a repeating event, select This Event Only to send
only this occurrence or Repeat Event to send all
instances.
Receiving Items
You receive a prompt when your phone has an
incoming transfer.
3. Select Bluetooth.
ᮣ
Press Accept (left softkey) to accept the transfer or
press Reject (right softkey) to reject the transfer.
4. Select a device or search for a device by selecting
[Find Devices].
5. If prompted, bond with the device. Your phone
Canceling Transfers
connects to the device and transfers the event.
You can cancel a transfer while in progress.
Sending Media Center Items
1. Press Cancel (right softkey).
You can only send audio files and pictures if they are
not forward locked and if their DRM settings do not
prevent you from sending them.
2. Press Yes (left softkey) to cancel press No (right
softkey) to continue with the transfer.
1. Press /> Media Center.
136
Viewing and Storing Received Items
After an incoming transfer is complete, your phone
translates the item and it appears on the display.
You can choose to either store or discard the item.
Items are stored as follows:
ⅷ Contact entries are stored to Contacts.
ⅷ Pictures and audio files are stored to their folders and
are accessible through the Media Center.
ⅷ Datebook events are stored to Datebook.
ᮣ
To store an item, press Store (left softkey).
ᮣ
To discard an item without saving it, press
Discard (right softkey).
137
Failure to read and follow the information provided in this phone
guide may result in serious bodily injury, death, or property
damage.
S1. Important Safety
Information
General Precautions
There are several simple guidelines to operating your phone
properly and maintaining safe, satisfactory service.
ࡗ ⅷ
To maximize performance, do not touch the bottom portion
of your phone where the internal antenna is located while
using the phone.
ࡗ ⅷ
ⅷ
Speak directly into the mouthpiece.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ Avoid exposing your phone and accessories to rain or liquid
spills. If your phone does get wet, immediately turn the
power off and remove the battery.
Do not expose your phone to direct sunlight for extended
periods of time (such as on the dashboard of a car).
Although your phone is quite sturdy, it is a complex piece of
equipment and can be broken. Avoid dropping, hitting,
bending, or sitting on it.
Any changes or modifications to your phone not expressly
approved in this document could void your warranty for this
equipment and void your authority to operate this
equipment.
ⅷ
ⅷ
ⅷ
For the best care of your phone, only authorized personnel
should service your phone and accessories. Failure to do
so may be dangerous and void your warranty.
Note
140
where use is forbidden or when it may cause interference or
danger.
Maintaining Safe Use of and Access
to Your Phone
Using Your Phone Near Other Electronic Devices
Most modern electronic equipment is shielded from radio
frequency (RF) signals. However, RF signals from wireless
phones may affect inadequately shielded electronic
equipment.
RF signals may affect improperly installed or inadequately
shielded electronic operating systems or entertainment
systems in motor vehicles. Check with the manufacturer or their
representative to determine if these systems are adequately
shielded from external RF signals. Also check with the
manufacturer regarding any equipment that has been added to
your vehicle.
Do Not Rely on Your Phone for Emergency Calls
Mobile phones operate using radio signals, which cannot
guarantee connection in all conditions. Therefore you should
never rely solely upon any mobile phone for essential
communication (e.g., medical emergencies). Emergency calls
may not be possible on all cellular networks or when certain
network services or mobile phone features are in use. Check
with your local service provider for details.
Using Your Phone While Driving
Consult the manufacturer of any personal medical devices,
such as pacemakers and hearing aids, to determine if they are
adequately shielded from external RF signals.
Talking on your phone while driving (or operating the phone
without a hands-free device) is prohibited in some jurisdictions.
Laws vary as to specific restrictions. Remember that safety
always comes first.
Operational Precautions
Responsible driving practices can be found in “Smart Practices
While Driving” on page 154 and/or at the Motorola website:
www.motorola.com/callsmart.
Always turn off the phone in healthcare facilities, and
request permission before using the phone near medical
equipment.
Note
Purchase an optional hands-free accessory at your local
Sprint Store, or call Nextel at 1-866-866-7509.
Tip
To assure optimal radio product performance and to be sure
that human exposure to RF does not exceed the guidelines set
forth in the relevant standards, always follow these instructions
and precautions:
Following Safety Guidelines
To operate your phone safely and efficiently, always follow any
special regulations in a given area. Turn your phone off in areas
141
neck, keep the device at least 2.5 centimeters (1 inch) from
your body when transmitting.
Phone Operation
When placing or receiving a phone call, hold your radio
product as you would a wireline telephone. Speak directly into
the microphone.
Approved Accessories
For a list of approved Motorola accessories call 1-800-453-0920, or
visit our website at www.motorola.com/support.
Two-way Radio Operation
Your radio product has been designed and tested to comply
with national and international standards and guidelines
regarding human exposure to RF electromagnetic energy,
when operated in the two-way mode (at the face, or at the
abdomen when using an audio accessory) at usage factors of
up to 50% talk/50% listen.
Transmit no more than the rated duty factor of 50% of the time.
To transmit (talk), push the PTT button. To receive calls, release
the PTT button. Transmitting 50% of the time or less, is
important because this radio generates measurable RF energy
only when transmitting (in terms of measuring for standards
compliance).
Turning Off Your Phone Before Flying
Turn off your phone before boarding any aircraft. To prevent
possible interference with aircraft systems, the U.S. Federal
Aviation Administration (FAA) regulations require you to have
permission from a crew member to use your phone while
the plane is on the ground. To prevent any risk of interference,
FCC regulations prohibit using your phone while the plane is in
the air.
Turning Off Your Phone in Dangerous Areas
To avoid interfering with blasting operations, turn your phone
off when in a blasting area or in other areas with signs
indicating two-way radios should be turned off. Construction
crews often use remote-control RF devices to set off explosives.
When using your radio product as a traditional
two-way radio, hold the radio product in a
vertical position with the microphone one to
two inches (2.5 to 5 cm) away from the lips.
Turn your phone off when you’re in any area that has a
potentially explosive atmosphere. Although it’s rare, your phone
and accessories could generate sparks. Sparks can cause an
explosion or fire, resulting in bodily injury or even death. These
areas are often, but not always, clearly marked. They include:
If you wear a radio product on your body when
transmitting, always place the radio product in
a Motorola approved clip, holder, holster, case
or body harness. If you do not use a body-worn accessory
supplied or approved by Motorola and are not using the radio
product in the intended use positions along side the head in
the phone mode or in front of the face in the two-way radio
mode, or if you hang your device from a lanyard around your
Ⅲ Fueling areas such as gas stations.
Ⅲ Below deck on boats.
Ⅲ Fuel or chemical transfer or storage facilities.
142
Ⅲ Areas where the air contains chemicals or particles such
as grain, dust, or metal powders.
Seizures/Blackouts
Some people may be susceptible to epileptic seizures or
blackouts when exposed to flashing lights, such as when
playing video games. These may occur even if a person has
never had a previous seizure or blackout.
If you have experienced seizures or blackouts, or if you have a
family history of such occurrences, please consult with your
physician before playing video games or enabling a flashing-
lights feature (if available) on your phone.
Discontinue use and consult a physician if any of the following
symptoms occur: convulsion, eye or muscle twitching, loss of
awareness, involuntary movements, or disorientation. It is
always a good idea to hold the screen away from your eyes,
leave the lights on in the room, take a 15-minute break every
hour, and stop use if you are very tired.
Ⅲ Any other area where you would normally be advised to
turn off your vehicle’s engine.
Never transport or store flammable gas, flammable liquids,
or explosives in the compartment of your vehicle that
contains your phone or accessories.
Note
Keep Your Mobile Device and Its Accessories Away From
Small Children
These products are not toys and may be hazardous to children.
For example:
A choking hazard may exist for small, detachable parts.
Improper use could result in loud sounds, possibly causing
hearing injury.
ⅷ
ⅷ
Caution About High Volume Usage
ⅷ
Improperly handled batteries could overheat and cause a
burn.
Do not allow children to play with your phone as they could
hurt themselves and others, damage the phone or make calls
that increase your invoice.
Exposure to loud noise from any source for
WARNING
extended periods of time may affect your hearing.
The louder the volume sound level, the less time is
required before your hearing could be affected.
Glass Parts
Some parts of your phone may be made of glass. This glass
could break if the product is dropped on a hard surface or
receives a substantial impact. If glass breaks, do not touch or
attempt to remove. Stop using your phone until the glass is
replaced by a qualified service center.
To protect your hearing:
ⅷ
Limit the amount of time you use headsets or headphones at
high volume.
ⅷ
Avoid turning up the volume to block out noisy surroundings.
143
ⅷ
Turn the volume down if you can’t hear people speaking
near you.
DON’Ts
ⅷ
Don’t disassemble, crush, puncture, shred, or otherwise
attempt to change the form of your battery.
If you experience hearing discomfort, including the sensation of
pressure or fullness in your ears, ringing in your ears, or
muffled speech, you should stop listening to the device through
your headset or headphones and have your hearing checked.
For more information about hearing, see our website at
direct.motorola.com/hellomoto/nss/AcousticSafety.asp (in
English only).
ⅷ
Don’t let the phone or battery come in contact with water.
Water can get into the phone’s circuits, leading to corrosion.
If the phone and/or battery get wet, have them checked by
your carrier or contact Motorola, even if they appear to be
working properly.
ⅷ
ⅷ
Don’t allow the battery to touch metal objects. If metal objects,
such as jewelry, stay in prolonged contact with the battery
contact points, the battery could become very hot.
Don’t place your battery near a heat source. Excessive heat
can damage the phone or the battery. High temperatures
can cause the battery to swell, leak, or malfunction.
Therefore:
Repetitive Motion
When you repetitively perform actions such as pressing keys or
entering finger-written characters, you may experience
occasional discomfort in your hands, arms, shoulders, neck, or
other parts of your body. If you continue to have discomfort
during or after such use, stop use and see a physician.
Ⅲ Do not dry a wet or damp battery with an appliance or
heat source, such as a hair dryer or microwave oven.
Ⅲ Avoid leaving your phone in your car in high
temperatures.
Battery Use and Safety
DOs
HANDLE AND STORE BATTERIES PROPERLY TO
Important
ⅷ
Do avoid dropping the battery or phone. Dropping these
AVOID INJURY OR DAMAGE. Most battery issues
arise from improper handling of batteries, and
particularly from the continued use of damaged
batteries.
items, especially on a hard surface, can potentially cause
damage.
ⅷ
Do contact your service provider or Motorola if your phone or
battery has been damaged from dropping or high
temperatures.
144
Proper and Safe Battery Disposal and Recycling
USE MOTOROLA ORIGINAL PRODUCTS FOR
QUALITY ASSURANCE AND SAFEGUARDS. To
aid consumers in identifying authentic Motorola
batteries from non-original or counterfeit batteries
(that may not have adequate safety protection),
Motorola provides holograms on its batteries.
Consumers should confirm that any battery they
purchase has a “Motorola Original” hologram.
Important
Proper battery disposal is not only important for safety, it
benefits the environment. Consumers may recycle their used
batteries in many retail or service provider locations. Additional
information on proper disposal and recycling may be found on
the Web:
ⅷ
www.motorola.com/recycling
ⅷ
www.rbrc.org/call2recycle/ (in English only)
Disposal of Lithium Ion (LiIon) Batteries: Promptly
dispose of used batteries in accordance with local
regulations. Contact your local recycling center or
national recycling organizations for more information
on how to dispose of batteries.
Motorola recommends you always use Motorola-branded
batteries and chargers. Motorola mobile devices are designed
to work with Motorola batteries. If you see a message on your
display such as Invalid Battery or Unable to Charge, take the
following steps:
ⅷ
Remove the battery and inspect it to confirm that it has a
“Motorola Original” hologram;
Do not handle a damaged or leaking Li-Ion battery as you can
be burned.
ⅷ
ⅷ
ⅷ
If there is no hologram, the battery is not a Motorola battery;
If there is a hologram, replace the battery and retry charging it;
If the message remains, contact a Motorola Authorized
Service Center.
Never dispose of batteries in a fire because they
may explode.
WARNING
Special Note: Be sure to dispose of your battery properly. In
some areas, the disposal of batteries in household or business
trash may be prohibited.
Motorola’s warranty does not cover damage to the
phone caused by non-Motorola batteries and/or
chargers.
Important
Protecting Your Battery
The guidelines listed below help you get the most out of your
battery’s performance.
Use of a non-Motorola battery or charger may
present a risk of fire, explosion, leakage, or other
hazard.
WARNING
ⅷ
Recently there have been some public reports of wireless
phone batteries overheating, catching fire, or exploding. It
appears that many, if not all, of these reports involve
145
counterfeit or inexpensive, aftermarket-brand batteries with
unknown or questionable manufacturing standards. Nextel is
not aware of similar problems with Nextel phones resulting
from the proper use of batteries and accessories approved
by Nextel or the manufacturer of your phone. Use only
Nextel-approved or manufacturer-approved batteries and
accessories found at Sprint Stores or through your phone’s
manufacturer, or call 1-866-866-7509 to order. They’re also
available at www.nextel.com — click Accessories. Buying the
right batteries and accessories is the best way to ensure
they’re genuine and safe.
Batteries and Chargers
Your battery, charger, or portable radio may contain symbols,
defined as follows:
Symbol
Definition
032374o
Important safety information follows.
Do not dispose of your battery or
phone in a fire.
ⅷ
ⅷ
In order to avoid damage, charge the battery only in
temperatures that range from 32° F to 113° F (0° C to 45° C).
Don’t use the battery charger in direct sunlight or in high
humidity areas, such as the bathroom.
Never dispose of the battery by incineration.
Keep the metal contacts on top of the battery clean.
Don’t attempt to disassemble or short-circuit the battery.
The battery may need recharging if it has not been used for
a long period of time.
Your battery or phone may require
recycling in accordance with local
laws. Contact your local regulatory
authorities for more information.
032375o
ⅷ
ⅷ
ⅷ
ⅷ
Do not throw your battery or phone
in the trash.
ⅷ
ⅷ
It’s best to replace the battery when it no longer provides
acceptable performance. It can be recharged hundreds of
times before it needs replacing.
Don’t store the battery in high temperature areas for long
periods of time. It’s best to follow these storage rules:
Your phone contains an internal
lithium ion battery.
Li Ion BATT
032378o
Do not let your battery, charger, or
phone get wet.
Less than one month:
-4° F to 140° F (-20° C to 60° C)
More than one month:
-4° F to 113° F (-20° C to 45° C)
Listening at full volume to music or
voice through a headset may
damage your hearing.
146
interference to hearing devices than unrated phones. (M4 is the
better/higher of the two ratings.)
T-Ratings: Phones rated T3 or T4 meet FCC requirements and
are likely to be more usable with a hearing device’s telecoil (“T
Switch”or “Telephone Switch”) than unrated phones. (T4 is the
better/higher of the two ratings. Note that not all hearing
devices have telecoils in them.)
Hearing aid devices may also be measured for immunity to
interference noise from wireless phones and should have
ratings similar to phones. Ask your hearing health care
professional for the rating of your hearing aid. Add the rating of
your hearing aid and your phone to determine probable
usability:
Using Your Phone With a Hearing
Aid Device
A number of Nextel phones have been tested for hearing aid
device compatibility. When some wireless phones are used
with certain hearing devices (including hearing aids and
cochlear implants), users may detect a noise which can
interfere with the effectiveness of the hearing device.
Some hearing devices are more immune than others to this
interference noise, and phones also vary in the amount of
interference noise they may generate. ANSI standard C63.19
was developed to provide a standardized means of measuring
both wireless phone and hearing devices to determine usability
rating categories for both.
Ratings have been developed for mobile phones to assist
hearing device users find phones that may be compatible with
their hearing device. Not all phones have been rated for
compatibility with hearing devices. Phones that have been
rated have a label with the rating(s) located on the box, and are
listed at www.motorola.com/accessibility.
These ratings are not guarantees. Results will vary depending
on the user’s hearing device and individual type and degree of
hearing loss. If a hearing device is particularly vulnerable to
interference noise; even a phone with a higher rating may still
cause unacceptable noise levels in the hearing device. Trying
out the phone with your hearing device is the best way to
evaluate it for your personal needs.
ⅷ
Any combined rating equal to or greater than six offers
excellent use.
ⅷ
ⅷ
Any combined rating equal to five is considered normal use.
Any combined rating equal to four is considered usable.
Thus, if you pair an M3 hearing aid with an M3 phone, you will
have a combined rating of six for “excellent use.”This is
synonymous for T ratings.
Nextel further suggests you experiment with multiple phones
(even those not labeled M3/T3 or M4/T4) while in the store to
find the one that works best with your hearing aid device.
Should you experience interference or find the quality of
service unsatisfactory after purchasing your phone, promptly
return it to the store within 30 days of purchase. With the Sprint
30-day Risk-Free Guarantee, you may return the phone within
30 days of purchase for a full refund. More information about
hearing aid compatibility may be found at:
M-Ratings: Phones rated M3 or M4 meet FCC requirements for
hearing aid compatibility and are likely to generate less
www.motorola.com/accessibility, www.fcc.gov, www.fda.gov,
and www.accesswireless.org.
147
accordance with the national collection and recycling schemes
operated by your local or regional authority. Alternatively, you
may return unwanted mobile devices and electrical
accessories to any Motorola Approved Service Center in your
region. Details of Motorola approved national recycling
schemes, and further information on Motorola recycling
activities can be found at: www.motorola.com/recycling.
Getting the Best Hearing Device
Experience With Your Phone
To further minimize interference:
ⅷ
Set the phone’s display and keyboard backlight settings to
ensure the minimum time interval:
1. Press /> Settings > Display/Info > Backlight > Timer or
Java Timer.
Disposal of your Mobile Device Packaging and User’s
Guide
2. Highlight the minimum time interval setting and press r.
Position the phone so the internal antenna is farthest from
your hearing aid.
Move the phone around to find the point with least
interference.
Product packaging and user’s guides should only be disposed
of in accordance with national collection and recycling
requirements. Please contact your regional authorities for more
details.
ⅷ
ⅷ
Export Law Assurances
Caring for the Environment by
Recycling
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the
exportation or re-exportation of this product to certain
destinations. For further information contact the U.S.
Department of Commerce or the Canadian Department of
Foreign Affairs and International Trade.
This symbol on a Motorola product means the product
should not be disposed of with household waste.
Disposal of your Mobile Device and Accessories
Please do not dispose of mobile devices or electrical
accessories (such as chargers, headsets, or batteries) with
your household waste. These items should be disposed of in
148
Operational Precautions
California Perchlorate Label
For optimal mobile device performance, and to be sure that
human exposure to RF energy does not exceed the guidelines
set forth in the relevant standards, always follow these
instructions and precautions.
Some mobile phones use an internal, permanent backup
battery on the printed circuit board that may contain very small
amounts of perchlorate. In such cases, California law requires
the following label:
Perchlorate Material – special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. There is no
special handling required by consumers.
Product Operation
When placing or receiving a phone call, hold your mobile
device just like you would a landline phone.
If you wear the mobile device on your body, always place the
mobile device in a Motorola-supplied or approved clip, holder,
holster, case, or body harness. If you do not use a body-worn
accessory supplied or approved by Motorola—or if you hang
your mobile device from a lanyard around your neck—keep the
mobile device and its antenna at least 2.5 centimeters (1 inch)
from your body when transmitting.
Using accessories not supplied or approved by Motorola may
cause your mobile device to exceed RF energy exposure
guidelines. For a list of Motorola-supplied or approved
accessories, visit our website at: www.motorola.com.
Radio Frequency (RF) Energy
This section contains important information on the safe and
efficient operation of your mobile device. Read this information
before using your mobile device.
Exposure to Radio Frequency (RF) Energy
Your mobile device contains a transmitter and receiver. When it
is ON, it receives and transmits RF energy. When you
communicate with your mobile device, the system handling
your call controls the power level at which your mobile device
transmits.
Your Motorola mobile device is designed to comply with local
regulatory requirements in your country concerning exposure
of human beings to RF energy.
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy
interference from external sources if inadequately shielded,
designed, or otherwise configured for RF energy compatibility.
In some circumstances your mobile device may cause
interference with other devices.
Follow Instructions to Avoid Interference Problems
ⅷ
Turn off your mobile device in any location where posted
notices instruct you to do so.
149
ⅷ
ⅷ
In an aircraft, turn off your mobile device whenever instructed
to do so by airline staff.
If your mobile device offers an airplane mode or similar
feature, consult airline staff about using it in flight.
Responsible driving practices can be found in the “Smart Practices
While Driving” section in this guide (or separate guide).
Operational Warnings
Obey all posted signs when using mobile devices in public areas.
Implantable Medical Devices
Potentially Explosive Atmospheres
If you have an implantable medical device, such as a
pacemaker or defibrillator, consult your physician before using
this mobile device.
Persons with implantable medical devices should observe the
following precautions:
Areas with potentially explosive atmospheres are often, but not
always, posted and can include fueling areas, such as below
decks on boats, fuel or chemical transfer or storage facilities, or
areas where the air contains chemicals or particles, such as
grain dust, or metal powders.
When you are in such an area, turn off your mobile device, and
do not remove, install, or charge batteries. In such areas,
sparks can occur and cause an explosion or fire.
ⅷ
ALWAYS keep the mobile device more than 20 centimeters
(8 inches) from the implantable medical device when the
mobile device is turned ON.
ⅷ
ⅷ
DO NOT carry the mobile device in the breast pocket.
Use the ear opposite the implantable medical device to
minimize the potential for interference.
Knowing Radio Frequency Safety
The design of your phone complies with updated NCRP standards
described below.
ⅷ
ⅷ
Turn OFF the mobile device immediately if you have any
reason to suspect that interference is taking place.
Read and follow the directions from the manufacturer of your
implantable medical device. If you have any questions about
using your mobile device with your implantable medical
device, consult your healthcare provider.
In 1991–92, the Institute of Electrical and Electronics Engineers
(IEEE) and the American National Standards Institute (ANSI) joined
in updating ANSI’s 1982 standard for safety levels with respect to
human exposure to RF signals. More than 120 scientists, engineers
and physicians from universities, government health agencies and
industries developed this updated standard after reviewing the
available body of research. In 1993, the Federal Communications
Commission (FCC) adopted this updated standard in a regulation.
In August 1996, the FCC adopted hybrid standard consisting of the
existing ANSI/IEEE standard and the guidelines published by the
National Council of Radiation Protection and Measurements
(NCRP).
Driving Precautions
The use of wireless phones while driving may cause distraction.
Discontinue a call if you can’t concentrate on driving.
Additionally, the use of wireless devices and their accessories
may be prohibited or restricted in certain areas. Always obey
the laws and regulations on the use of these products.
150
ⅷ
ⅷ
Australian Communications Authority Radio
communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
ANATEL, Brazil Regulatory Authority, Resolution 303 (July 2,
2002) “Regulation of the limitation of exposure to electrical,
magnetic, and electromagnetic fields in the radio frequency
range between 9 kHz and 300 GHz.” “Attachment to
Resolution 303 from July 2, 2002.”
Body-Worn Operation
To maintain compliance with FCC RF exposure guidelines, if
you wear a handset on your body, use the Motorola supplied or
approved carrying case, holster or other body-worn accessory.
If you do not use a body-worn accessory, ensure the antenna is
at least 2.5 centimeters from your body when transmitting. Use
of non-Motorola-approved accessories may violate FCC RF
exposure guidelines.
Your Motorola phone is designed to comply with local
regulatory requirements in your country concerning exposure
of human beings to RF energy.
For more information about RF exposure, visit the FCC website
at www.fcc.gov.
Specific Absorption Rate
Your Motorola Clutch i465 model wireless phone meets the
governmental requirements for exposure to radio waves.
Your wireless phone is a radio transmitter and receiver. It is
designed and manufactured to not exceed limits for exposure
to radio frequency (RF) energy set by the Federal
PortableRadio Product Operation and EME Exposure
Communications Commission (FCC) of the U.S. Government
and by the Canadian regulatory authorities. These limits are
part of comprehensive guidelines and establish permitted
levels of RF energy for the general population. The guidelines
are based on standards that were developed by independent
scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a
substantial safety margin designed for the safety of all persons,
regardless of age or health, and to account for any variations in
measurements.
ⅷ
Your Motorola radio product is designed to comply with the
following national and international standards and guidelines
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
United States Federal Communications Commission, Code
of Federal Regulations; 47 CFR part 2 sub-part J.
ⅷ
ⅷ
ⅷ
ⅷ
ⅷ
American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
Institute of Electrical and Electronics Engineers (IEEE). C95.
1-2005 Edition.1
International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
Ministry of Health (Canada). Safety Code 6. Limits of Human
Exposure to Radio frequency Electromagnetic Fields in the
Frequency Range from 3 kHz to 300 GHz, 1999.
1.The information provided in this document supersedes the
general safety information in user’s guides published prior to
May 1, 2006
151
The exposure standard for wireless mobile phones employs a
unit of measurement known as the Specific Absorption Rate
(SAR). The SAR limit set by the FCC and by the Canadian
regulatory authorities is 1.6 watts per kilogram (W/kg),
averaged over one gram of tissue. Tests for SAR are conducted
using procedures accepted by the FCC and by Industry
Canada with the phone transmitting at its highest certified
power level in all tested frequencies. Although the SAR is
determined at the highest certified power level, the actual SAR
level of the phone while operating can be below the maximum
value. This is because the phone is designed to operate at
multiple power levels so as to use only the power required to
reach the network. In general, the closer you are to a wireless
base station, the lower the power output.
Before a phone model is available for sale to the public in the
U.S. and Canada, it must be tested and certified to the FCC
and Industry Canada that it does not exceed the limit
established by each government for safe exposure. The tests
are performed in positions and locations (e.g., at the ear and
worn on the body) submitted to the FCC and available for
review by Industry Canada. The highest SAR value for this
model phone when tested for use at the ear is 1.17W/kg, and
when worn on the body, as described in this user guide, is 1.41
W/kg. Body-worn measurements can differ, depending upon
available accessories and regulatory requirements. The SAR
information includes the Motorola testing protocol, assessment
procedure, and measurement uncertainty range for this
product.
the SAR value for later products; in all cases, products are
designed to be within the guidelines.
Additional information on SAR can be found on the Cellular
Telecommunications & Internet Association (CTIA) website:
www.phonefacts.net
or the Canadian Wireless Telecommunications Association
(CWTA) website: www.cwta.ca.
Owner’s Record
The model number, regulatory number, and serial number are
located on a nameplate inside the battery compartment.
Record the serial number in the space provided below. This will
be helpful if you need to contact us about your phone in the
future.
Model: MotorolaClutch i465
Serial No.:
Online Product Registration:
http://www.motorola.com/us/productregistration
Product registration is an important step toward enjoying your
new Motorola product. Registration permits us to contact you
for product or software updates and allows you to subscribe to
updates on new products or special promotions. Registration is
not required for warranty coverage. Please retain your original
dated sales receipt, as you may need to provide it for warranty
validation in the future.
While there may be differences between the SAR levels of
various phones and at various positions, they meet the
governmental requirements for safe exposure. Please note that
improvements to this product model could cause differences in
Thank you for choosing a Motorola product.
152
Patent and Trademark Information
Software Copyright Notice
MOTOROLA, the Stylized M Logo and all other trademarks
indicated as such herein are trademarks of Motorola, Inc.
® Reg. U.S. Pat. & Tm. Off. © 2009 Motorola, Inc. All rights
reserved.
Microsoft and Microsoft Internet Explorer are registered
trademarks of Microsoft Corporation.
This product is covered by U.S. Pat. 5,818,437, U.S. Pat.
5,953,541, U.S. Pat. 6,011,554 and other patents pending.
Java and all other Java-based marks are trademarks or
registered trademarks of Sun Microsystems, Inc. in the U.S. and
other countries.
The Motorola products described in this manual may include
copyrighted Motorola and third party software stored in
semiconductor memories or other media. Laws in the United
States and other countries preserve for Motorola and third party
software providers certain exclusive rights for copyrighted
software, such as the exclusive rights to distribute or reproduce
the copyrighted software. Accordingly, any copyrighted
software contained in the Motorola products may not be
modified, reverse-engineered, distributed, or reproduced in any
manner to the extent allowed by law. Furthermore, the
purchase of the Motorola products shall not be deemed to
grant either directly or by implication, estoppel, or otherwise,
any license under the copyrights, patents, or patent
All other product names or services mentioned in this manual
are the property of their respective trademark owners.
applications of Motorola or any third party software provider,
except for the normal, non-exclusive, royalty-free license to use
that arises by operation of law in the sale of a product.
153
Privacy and Data Security
Smart Practices While Driving
Drive Safe, Call Smart SM
Motorola understands that privacy and data security are
important to everyone. Because some features of your phone
may affect your privacy or data security, please follow these
recommendations to enhance protection of your information:
Check the laws and regulations on the use of mobile devices
and their accessories in the areas where you drive. Always
obey them. The use of these devices may be prohibited or
restricted in certain areas. Contact www.motorola.com/callsmart
for more information.
Your mobile device lets you communicate by voice and data—
almost anywhere, anytime, wherever wireless service is
available and safe conditions allow. When driving a car, driving
is your first responsibility. If you choose to use your mobile
device while driving, remember the following tips:
ⅷ
Monitor access: Keep your phone with you and do not leave
it where others may have unmonitored access. Lock your
device’s keypad where this feature is available.
ⅷ
Keep software up to date: If Motorola or a software/
application vendor releases a patch or software fix for your
phone which updates the device’s security, install it as soon
as possible.
ⅷ
Erase before recycling: Delete personal information or data
from your phone prior to disposing of it or turning it in for
recycling. For step-by-step instructions on how to delete all
personal information from your device, please contact your
local service provider.
ⅷ
Get to know your Motorola phone and its features such as
speed dial and redial. If available, these features help you to
place your call without taking your attention off the road.
ⅷ
When available, use a hands-free device. If possible, add an
additional layer of convenience to your phone with one of the
many Motorola Original hands-free accessories available
today.
ⅷ
Understanding AGPS: In order to comply with emergency
caller location requirements of the FCC, certain Motorola
phones incorporate Assisted Global Positioning System
(AGPS) technology. AGPS technology also can be used in
non-emergency applications to track and monitor a user’s
location, for example, to provide driving directions. Users
who prefer not to permit such tracking and monitoring
should avoid using such applications.
ⅷ
ⅷ
Position your phone within easy reach. Be able to access
your phone without removing your eyes from the road. If you
receive an incoming call at an inconvenient time, if possible,
let your voice mail answer it for you.
Let the person you are speaking with know you are driving; if
necessary, suspend the call in heavy traffic or hazardous
weather conditions. Rain, sleet, snow, ice, and even heavy
traffic can be hazardous.
If you have further questions regarding how use of your phone
may impact your privacy or data security, please contact
Motorola.
154
ⅷ
ⅷ
ⅷ
Do not take notes or look up phone numbers while driving.
Jotting down a “to do” list or going through your address
book takes attention away from your primary responsibility,
driving safely.
Dial sensibly and assess the traffic; if possible, place calls
when your car is not moving or before pulling into traffic. If
you must make a call while moving, dial only a few numbers,
check the road and your mirrors, then continue.
Do not engage in stressful or emotional conversations that
may be distracting. Make people you are talking with aware
you are driving and suspend conversations that can divert
your attention away from the road.
ⅷ
ⅷ
Use your phone to call for help. Dial 911 or other local
emergency number in the case of fire, traffic accident, or
medical emergencies.*
Use your phone to help others in emergencies. If you see an
auto accident, crime in progress, or other serious emergency
where lives are in danger, call 911 or other local emergency
number, as you would want others to do for you.*
ⅷ
Call roadside assistance or a special non-emergency
wireless assistance number when necessary. If you see a
broken-down vehicle posing no serious hazard, a broken
traffic signal, a minor traffic accident where no one appears
injured, or a vehicle you know to be stolen, call roadside
assistance or other special non-emergency wireless
number.*
* Wherever wireless phone service is available
155
Motorola Limited Warranty
for the United States and Canada
S2. Manufacturer’s Warranty
What does this Warranty Cover?
Subject to the exclusions contained below, Motorola, Inc.
warrants its telephones, pagers, messaging devices, and
consumer and professional two-way radios (excluding
commercial, government or industrial radios) that operate via
Family Radio Service or General Mobile Radio Service,
Motorola-branded or certified accessories sold for use with
these Products (“Accessories”) and Motorola software
contained on CD-ROMs or other tangible media and sold for
use with these Products (“Software”) to be free from defects in
materials and workmanship under normal consumer usage for
the period(s) outlined below. This limited warranty is a
consumer's exclusive remedy, and applies as follows to new
Motorola Products, Accessories and Software purchased by
consumers in the United States or Canada, which are
accompanied by this written warranty:
ࡗ ࡗ Your phone has been designed to provide you with reliable, worry-free
service. If for any reason you have a problem with your
equipment, please refer to the manufacturer’s warranty in this
section.
For information regarding the terms and conditions of service
for your phone, please visit www.nextel.com or call Nextel
Customer Service at 1-800-639-6111.
156
Products and Accessories
Products Covered
Length of Coverage
Products and
Accessories that are
Repaired or
The balance of the original
warranty or for ninety (90) days
from the date returned to the
consumer, whichever is longer.
Products Covered
Length of Coverage
Products and
One (1) year from the date of
purchase by the first
consumer purchaser of the
product unless otherwise
provided for below.
Accessories as
defined above,
unless otherwise
provided for below.
Replaced.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Decorative
Limited lifetime warranty for the
lifetime of ownership by the first
consumer purchaser of the
product.
Accessories and
Cases. Decorative
covers, bezels,
PhoneWrap™ covers
and cases.
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are
covered by this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or
neglect, such as physical damage (cracks, scratches, etc.) to
the surface of the product resulting from misuse; (b) contact
with liquid, water, rain, extreme humidity or heavy perspiration,
sand, dirt or the like, extreme heat, or food; (c) use of the
Products or Accessories for commercial purposes or
subjecting the Product or Accessory to abnormal usage or
conditions; or (d) other acts which are not the fault of Motorola,
are excluded from coverage.
Monaural Headsets.
Ear buds and boom
headsets that
transmit mono sound
through a wired
connection.
Limited lifetime warranty for the
lifetime of ownership by the first
consumer purchaser of the
product.
Consumer and
Professional
Two-Way Radio
Accessories.
Ninety (90) days from the date of
purchase by the first consumer
purchaser of the product.
Use of Non-Motorola Products and Accessories. Defects or
damage that result from the use of
157
Non-Motorola branded or certified Products, Accessories,
Software or other peripheral equipment are excluded from
coverage.
Software
Products Covered
Length of Coverage
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by
someone other than Motorola, or its authorized service centers,
are excluded from coverage.
Ninety (90) days from
the date of purchase.
Software. Applies only to
physical defects in the media
that embodies the copy of the
software (e.g. CD-ROM, or
floppy disk).
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola housings, or parts, are
excluded from coverage.
Exclusions
Software Embodied in Physical Media. No warranty is made
that the software will meet your requirements or will work in
combination with any hardware or software applications
provided by third parties, that the operation of the software
products will be uninterrupted or error free, or that all defects in
the software products will be corrected.
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication
service or signal you may subscribe to or use with the Products
Accessories or Software is excluded from coverage.
Software NOT Embodied in Physical Media. Software that is not
embodied in physical media (e.g. software that is downloaded
from the internet), is provided “as is” and without warranty.
Who Is Covered?
This warranty extends only to the first consumer purchaser, and
is not transferable.
158
(a) a copy of your receipt, bill of sale or other comparable proof
of purchase; (b) a written description of the problem; (c) the
name of your service provider, if applicable; (d) the name and
location of the installation facility (if applicable) and, most
importantly; (e) your address and telephone number.
What Will Motorola Do?
Motorola, at its option, will at no charge repair, replace or refund
the purchase price of any Products, Accessories or Software
that does not conform to this warranty. We may use functionally
equivalent reconditioned/refurbished/pre-owned or new
Products, Accessories or parts. No data, software or
applications added to your Product, Accessory or Software,
including but not limited to personal contacts, games and
ringer tones, will be reinstalled. To avoid losing such data,
software and applications please create a back up prior to
requesting service.
What other limitations are there?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS
EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT
SHALL MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR
TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS
OF THE PURCHASE PRICE OF THE PRODUCT, ACCESSORY
OR SOFTWARE, OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR
LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS
OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS
OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE ABILITY OR INABILITY TO USE THE
PRODUCTS, ACCESSORIES OR SOFTWARE TO THE FULL
EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
How to Obtain Warranty Service or Other
Information
USA
Phones
1-800-453-0920
1-877-483-2840
TTY
For Accessories and Software, please call the
telephone number designated above for the product
with which they are used
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include:
159
Some states and jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the length of an
implied warranty, so the above limitations or exclusions may not apply
to you. This warranty gives you specific legal rights, and you may also
have other rights that vary from state to state or from one jurisdiction to
another.
Service and Repairs
If you have questions or need assistance, we’re here to help.
a number of customer care options. You can also contact the
Motorola Customer Support Center at 1-800-453-0920 (United
States), 1-877-483-2840 (TTY/TDD United States for hearing
impaired).
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce and
distribute copies of the Motorola software. Motorola software
may only be copied into, used in, and redistributed with, the
Products associated with such Motorola software. No other use,
including without limitation disassembly of such Motorola
software or exercise of the exclusive rights reserved for
Motorola, is permitted.
160
Making Calls From Datebook
108
Using Your Phone’s
Dialing Codes
Direct Talk
Non-Emergency Numbers
Telecommunications Relay
Digital Rights Management,
Receiving All Calls On
Making Direct Connect Calls
Direct Connect
Direct Connect Calls
D
Datebook
Direct Connect Number
162
Viewing License Information
Group Connect
J
E
Suspending Applications
H
I
G
K
L
Icons
Lock Code
163
M
Multimedia Messages
Media Center
Messages
My Info
Messaging Settings
N
Nextel Direct Send
Nextel Direct Talk
Memory
Nextel Service
Menu
Notepad
164
O
P
Remote Direct Connect Button
Ring Tones
Phone Number
S
Shortcuts
Q
R
165
SIM Card
Speed Dial
Transmitters
Turning Your Phone On and
Voicemail
U
V
W
Waits
T
Telecommunications Relay
Voice Records
Text Messaging
166
|
