User's Guide
SERIES TWO-WAY RADIO
Models CLS1110 and CLS1410
@6864110W15@
6864110W15-A
Contents
Introduction....................................2
FCC Licensing Information.......... 4
Safety and General Information .. 6
Radio Controls.............................13
Getting Started.............................14
Installing the Swivel Belt
Holster ....................................14
Installing the Batteries................15
Charging the Battery..................16
Turning Your Radio On and Off .19
Adjusting the Volume.................20
Reading the Display...................20
Talking and Receiving.................21
Basic Radio Operation...............21
Signal Strength and
Programming Mode.....................26
Factory Default Settings.............27
Entering Programming Mode .....28
Cloning Radio Settings ...............32
Advanced Features......................33
Troubleshooting .........................35
Use and Care................................38
Frequencies and Bandwidths.....39
Spirit GT Series Programming ...45
Warranty .......................................46
Channel Busy Indicators.........21
Talk Range.................................22
Handsfree Use (VOX)
(CLS1410 only).......................22
Locking the Keypad ...................23
Monitoring a Channel.................24
Scanning (CLS1410 Only) .........24
1
Introduction
Thank you for purchasing a Motorola _Series Radio. Your radio is a product of
Motorola’s 70 plus years of experience as a world leader in designing and
manufacturing communications equipment. The _Series radios provide cost-
effective communications for businesses such as retail stores, restaurants, hotels,
and schools. Motorola professional two-way radios are the perfect communications
solution for all of today’s fast-paced industries.
Please read this guide carefully so you know how to properly operate the radio
before use.
Package Contents
•
•
•
•
•
•
•
_Series Radio
Swivel Belt Holster
Lithium Ion Battery
Drop-In Charger with Transformer
User's Guide
Accessory Brochure
Warranty Card
2
For product-related questions, please call:
1-800-448-6686 in the USA
1-888-390-6456 TTY (Text Telephone)
On the Web:
ATTENTION
Before using this product, read the RF energy awareness information and operating
instructions in the Safety and General Information section of this guide to ensure
compliance with RF energy exposure limits.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or
service names are the property of their respective owners.
© Motorola, Inc. 2003.
3
FCC Licensing Information
_Series professional two-way radios operate on radio frequencies that are regulated by the Federal
Communications Commission (FCC). In order to transmit on these frequencies, you are required to have a
license issued by the FCC.
Application is made available on FCC Forms 601, schedules D and H, and remittance form 159. If ordering the
forms by mail, phone, or from the FCC website, please request document number 000601, which includes all
forms and instructions. If using the FCC Fax-on-Demand system, use the 7-digit order numbers listed below.
To obtain the required forms, please use the following contact information:
By Phone or Web
Faxed
Mailed
or for questions
contact the Fax-On-Demand call the FCC forms hotline
regarding FCC license
system at:
at:
contact the FCC at:
1-888-CALL-FCC
1-888-225-5322
1-800-418-FORM
1-800-418-3676
1-202-418-0177
Request forms 3060001,
3060003, and 3060006
Request document 000601
Request document 000601
Before filling out your application, you must decide which frequency(ies) you can operate on. See Frequencies
and Bandwidths on page 39. For questions on determining your radio frequency, please call Motorola Product
Services at 1-800-448-6686.
Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC
to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should
4
be made only by or under the supervision of a person certified as technically qualified to perform transmitter
maintenance and repairs in the private land mobile and fixed services as certified by an organization
representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor,
etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be distributed is subject to government
regulations and may be prohibited.
5
Safety and General Information
Important Information on Safe and Efficient Operation.
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general safety information contained in user guides
published prior to December 1, 2002.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control your exposure and ensure compliance with
the occupational/controlled environment exposure limits, always adhere to the following procedure:
•
•
•
Transmit no more than 50% of the time.
To transmit (talk), press the Push to Talk (PTT) button.
To receive calls, release the PTT button.
Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure
only when transmitting (in terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola radio is designed to comply with the following national and international standards and guidelines
regarding exposure of human beings to radio frequency electromagnetic energy:
•
United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-
part J
•
American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95.
1-1992
6
•
•
•
Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radio Frequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz, 1999
•
•
Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human
Exposure) Standard 2001 (applicable to wireless phones only)
ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2002) “additional requirements for SMR,
cellular, and PCS product certification.”
To assure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy
is within the guidelines set forth in the above standards, always adhere to the following procedures.
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or
attachments could damage the radio and may violate FCC regulations.
DO NOT hold the antenna when the radio is “IN USE.” Holding the antenna affects the effective range.
Two-Way Radio Operation
When using your radio as a traditional two-way radio, hold the radio in a vertical position
with the microphone 1 to 2 inches (2.5 to 5 cm) away from the lips
.
7
Body-Worn Operation
To maintain compliance with FCC/Health Canada RF exposure guidelines, if you wear a radio on your body
when transmitting, always place the radio in a Motorola-supplied or approved clip, holder, holster, case, or body
harness for this product. Use of non-Motorola-approved accessories may exceed FCC/Health Canada RF
exposure guidelines. If you do not use one of the Motorola-supplied or approved body-worn accessories, and
are not using the radio held in the normal use position, ensure the radio and its antenna are at least 1 inch
(2.5 cm) from your body when transmitting
.
Data Operation
If applicable, when using any data feature of the radio with or without an accessory cable, position the radio
and its antenna at least 1 inch (2.5 cm) from the body
.
Approved Accessories
For a list of approved Motorola accessories visit our website at www.motorola.com
.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately
shielded, designed, or otherwise configured for electromagnetic compatibility.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where
posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive
to external RF energy.
8
Aircraft
When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in
accordance with applicable regulations per airline crew instructions.
Medical Devices - Pacemakers
The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be
maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with
the independent research by, and recommendations of the U.S. Food and Drug Administration.
Persons with pacemakers should:
•
•
•
•
ALWAYS keep the radio more than six inches (15 cm) from their pacemaker when the radio is turned ON.
Not carry the radio in the breast pocket.
Use the ear opposite the pacemaker to minimize the potential for interference.
Turn the radio OFF immediately if you have any reason to suspect that interference is taking place.
Medical Devices - Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may
want to consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your device to determine if it is
adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.
9
Safety and General Use While Driving
Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using
your radio while driving, please:
•
•
•
Give full attention to driving and to the road.
Use hands-free operation, if available.
Pull off the road and park before making or answering a call if driving conditions so require.
Operational Warnings
For Vehicles with an Air Bag
Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with
great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be
propelled with great force and cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive atmosphere, unless it is a radio type
especially qualified for use in such areas as “Intrinsically Safe.” Do not remove, install, or charge batteries in
such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury
or even death.
Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as below
decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles,
such as grain, dust or metal powders, and any other area where you would normally be advised to turn off your
vehicle engine. Areas with potentially explosive atmospheres are often but not always posted.
10
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting
caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Obey all signs and instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with
your skin, a minor burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as
jewelry, keys, or beaded chains touch exposed terminals. The conductive material may complete an electrical
circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when
placing it inside a pocket, purse, or other container with metal objects.
Battery Charger Safety Instructions
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged
in any way.
3. Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet
installed by a qualified electrician. An improper condition can result in a risk of electric shock.
11
4. To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the
charger from the AC receptacle.
5. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance
or cleaning.
6. Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock, or
personal injury.
7. Make sure the cord is located so it will not be stepped on, tripped over, or subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord
could result in a risk of fire and/or electric shock. If an extension cord must be used, make sure that:
•
The pins on the plug of the extension cord are the same number, size, and shape as those on the plug of
the charger.
•
•
The extension cord is properly wired and in good electrical condition.
The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150 feet.
9. The supply cord of this charger cannot be replaced. If the cord is damaged, call Motorola Product Services
at 1-800-448-6686 in the USA or 1-888-390-6456 TTY (Text Telephone).
12
Radio Controls
Microphone
Use Pto:
Turn radio on/off
Adjust radio volume
Use Bto:
Transmit call tone
Accessory Jack
Use Push to Talk to:
Talk
Exit a menu
Use [ and ] to:
Change channels
(CLS1410 only)
Use T to:
Monitor the frequency
Change menu settings
Scan channels (CLS1410 only)
Speaker
Use S to:
Lock the keypad
Scroll through menus
13
Getting Started
Installing the Swivel Belt Holster
1. Slide the bottom of the radio into the holster until it snaps
into place.
2. To remove, push the tab on the holster and pull the radio
away from the holster.
Note: In case of loss, please contact your point-of-sale or
call 1-800-448-6686 to request replacement part
number HCLN4013.
56532 Swivel
Belt Holster
0
14
Installing the Batteries
Your radio uses a rechargeable Lithium Ion (Li Ion) battery or 3 AAA alkaline batteries
with the 56564 AAA Battery Tray (not included with all models).
Li Ion Battery
1. If the battery door is already in place, push down on the
recess on the door and slide it off the radio.
2. Insert the battery, printed arrows first, into the battery
compartment and press down to secure firmly in place.
3. Slide and snap the battery door into place.
AAA Alkaline Batteries
1. If the battery door is already in place, push down on the
recess on the door and slide it off the radio.
2. Insert 3 AAA batteries into the battery tray as shown by
the markings inside the tray.
3. Insert the battery tray into the battery compartment and press down to secure
firmly in place.
4. Slide and snap the battery door into place.
5. Press S until A or nflashes (this menu does not appear if using a Motorola
Li Ion battery).
6. Press [ or ] to select A for alkaline batteries, or n for rechargeable AAA cells.
15
Charging the Battery
Use only the charger supplied with the radio, or other _Series power
accessories. For optimum battery life, do not charge the battery for prolonged periods
after it is fully charged. Charging the battery over the weekend is acceptable.
Using the Drop-in Charger
1. Place the charger on a flat surface.
2. Insert the plug of the power cord into the jack
on the charger.
3. Plug the cord into an AC outlet.
4. Turn the radio off. If the radio is on while
charging, it will take longer to fully charge.
5. Insert the radio (with battery installed) into
the front charging pocket.
Note: The radio will fit in the charger with the
holster on.
The drop-in charger will also sequentially charge a spare SNN5571 Li Ion battery.
The spare battery will not begin to charge until the radio battery is fully charged. Both
batteries will charge in approximately
2–6 hours.
16
Using the 56531 Multi-Unit Charger
The Multi-Unit Charger (MUC) allows drop-in charging of up to 6 radios or batteries.
Batteries can be charged inside the radios or removed and placed in the MUC
separately. Each of the 6 charging pockets can hold a radio or battery, but not both.
1. Place the charger on a flat surface.
2. Insert the power cord plug into the jack on the MUC.
3. Plug the cord into an AC outlet.
4. Turn the radio off.
5. Insert the radio or battery into the charging pocket.
Battery charging pocket
Radio charging pocket
17
Charging Status LEDs
On the drop-in charger, the radio and battery charging pockets have their own LEDs.
On the MUC, each of the 6 charging pockets has an LED. The LEDs are grouped into
pairs to show which charging pockets are paired (for cloning, see page 32).
The LED is solid red when the battery is charging, and solid green when charging is
complete.
Battery Meter
The battery meter in the upper left corner of the display (see page 20) shows how
much battery power is remaining.
Battery Type
3 Bars
2 Bars
1 Bar
Flashing
d
b
c
m
Li Ion
100%–85%
85%–25%
75%–40%
25%–10%
40%–10%
Final 10%
Final 10%
AAA Alkaline 100%–75%
Battery Life
Based on 5% transmit, 5% receive, 90% standby (standard duty cycle):
Li Ion – 12 Hours AAA Alkaline – 10 Hours
Note: For optimal battery life, high-capacity alkaline batteries are recommended.
18
Turning Your Radio On and Off
See page 13 for a basic radio diagram.
3 seconds.
When you turn the radio on, the radio chirps and the display briefly
shows all features and display segments.
The radio then displays the current channel (larger number in the
center) and the frequency assigned to that channel (on the right
indicated by l).
The Interference Eliminator Code displays briefly (indicated by
y), then the current channel remains displayed.
19
Adjusting the Volume
Turn Pclockwise to increase the volume, and counterclockwise to decrease the
volume.
Note: Do not hold the radio too close to your ear when adjusting the volume.
Reading the Display
®
VibraCall Alert Indicator
Signal Strength and Channel Busy Indicator
Frequency and
Interference Eliminator
Code
Battery Meter
Channel
Keypad Lock
Interference Eliminator
Code Indicator
Frequency Indicator
Programming Mode
Microphone Gain and
VOX (CLS1410 only)
Scan (CLS1410 Only)
20
Talking and Receiving
Basic Radio Operation
1. Press and hold T to check for channel activity. If you hear static, the channel is
clear to use. Do not transmit if someone is speaking on the channel. Press
again to stop monitoring.
T
2. To talk, press and hold Push to Talk and speak into the microphone. Hold the
radio 2 to 3 inches away from your mouth.
3. To listen, release Push to Talk
.
The transmit LED on the top of the radio is red when transmitting.
Signal Strength and Channel Busy Indicators
When there is activity on a frequency, the radio displays w and the
transmit light flashes at a faster rate of once per second.
When there is activity on the same frequency and code as your radio
(your radio is receiving), the radio displays w and a signal strength
from 1 (weakest) to 6 (strongest). This can help determine when a
radio is moving out of range.
Note: Obstacles that block the signal path may affect the strength of the incoming
signal.
21
Talk Range
Industrial
Multi-Level
Outdoor
Inside steel/concrete
industrial buildings
Inside multi-level
buildings
Flat ground with no
obstructions
Up to 200,000 sq. ft.
Up to 15 floors
Up to 5 miles
Handsfree Use (VOX) (CLS1410 only)
The CLS1410 model radio can operate handsfree when used with compatible voice
activation (VOX) accessories. A short delay occurs between the time when you start
talking and when the radio transmits.
With Compatible VOX Accessories
1. Turn the radio off.
2. Open the accessory cover.
3. Plug the audio accessory firmly into the accessory jack.
4. Turn the radio on. The radio displays g. If gis flashing
and you are setting up the VOX accessory for the first
time, set the VOX sensitivity level (see page 23).
5. Lower the radio volume BEFORE placing the accessory
in or near your ear.
22
6. To transmit, speak into the accessory microphone. To receive, stop talking.
To disable VOX operation, press Push to Talk or remove the audio accessory.
call 1-800-448-6686, or contact your point of purchase.
Setting the
VOX Sensitivity
You can adjust the sensitivity of your radio’s accessory or microphone during VOX
operation to suit different operating environments. These menus appear only when
the VOX feature is in use, which is indicated by g.
1. Press
until g displays. The radio displays Hwhen you are
S
setting the external VOX (with audio accessory).
2. Press or to select the sensitivity level:
[
]
0= Off 1= Low 2= Medium 3= High
External VOX
Locking the Keypad
You can lock the keypad to avoid accidentally changing your radio settings.
1. Press and hold for 3 seconds.
S
2. To unlock, press and hold
for 3 seconds.
S
23
Monitoring a Channel
Monitoring allows you to check for activity on a channel.
1. Press and hold T. If the channel is clear to use, you will hear
static and w and 0will display.
2. Press T again to stop monitoring.
Scanning (CLS1410 Only)
You can scan up to 4 channels and frequencies. When the radio
detects activity, it stops scanning and locks in on the active channel. This allows you
to talk and listen to the person transmitting without changing channels.
1. To start scanning, briefly press T.
The scan icon h displays and the radio begins to scan the channels. When the
radio detects activity, it stops on that channel and displays w and the channel
number.
2. To talk to the person transmitting without switching channels, press Push to Talk
within 5 seconds. If no transmission occurs within 5 seconds, scanning resumes.
3. To stop scanning, briefly press T.
If you press Push to Talk while the radio is scanning, the radio transmits on the
channel you were on before you started scanning.
24
Skipping and Removing Channels While Scanning
Scan has two temporary features to make it easier to use.
•
Scan advance
If the radio stops scanning on a channel you do not want to listen to, press ] to
resume scanning for the next active channel.
Nuisance delete
•
Press and hold [ to temporarily remove a channel from the scan list. The
channel return the next time you use the scan feature.
25
Programming Mode
Programming mode allows you to change the following settings on your radio:
•
•
•
•
•
•
•
Channel
Frequency
Interference eliminator code
Call tones
Microphone gain
Scan list (CLS1410 only)
Available channels (CLS1410 only)
Notes:
•
To talk with someone on your two-way radio, the channel (CLS1410 only),
frequency, and interference eliminator code must be the same on both radios.
You cannot enter programming mode while a VOX accessory is plugged into the
radio.
•
26
Factory Default Settings
Your radio is programmed at the factory to the following settings:
Frequency
CLS1110
CLS1410
Channel
1
2
2
8
5
6
2
3
4
Not available
1
Code
Call Tone/
Off (0)
Not available
®
VibraCall
VOX
Off (0)
Microphone
Gain
2 (medium sensitivity)
To restore the factory settings, turn the radio on while holding Push to Talk and S
for 3 seconds.
27
Entering Programming Mode
Press and hold Push to Talk and T for 3 seconds while turning the radio on. The
radio beeps and displays k, the channel number flashes, and the frequency
(indicated by l) and code (indicated by y) display alternately.
Note: If you press and release the Push to Talk button when programming
CSL1410 models, you will return to the front of the Programming Mode.
Selecting a Channel (CLS1410 Only)
1. In programming mode, press
until the channel number flashes
S
and the frequency and code display alternately (this is the first
setting after you enter programming mode).
2. Press [ or ] to select the channel.
3. Press and hold Push to Talk to exit programming mode, or
press
to continue programming.
S
Programming the Frequency
1. In programming mode, press
frequency number flashes.
until l displays and the
S
2. Press
or
to select the frequency.
[
]
3. Press and hold Push to Talk to exit programming mode, or
press to continue programming.
Note: See page 39 for information on frequencies for communicating with other
business radios. If you are matching your _Series radio to an existing Spirit GT
radio, see page 45.
S
28
Programming the Interference Eliminator Code
The interference eliminator code helps minimize interference by providing code
combinations that filter out static, noise, and unwanted messages.
1. In programming mode, press S until ydisplays and the code
number flashes.
2. Press
or
to select the code (see page 42).
[
]
3. Press and hold Push to Talk to exit programming mode, or press
to continue programming.
Programming the Available Channels (CLS1410 only)
S
If you need fewer channels, you can reduce the number of available channels.
1. In programming mode, press S until =displays and the channel
number flashes.
2. Press
or
to select the number of channels you want
[
]
available.
3. Press and hold Push to Talk to exit programming mode, or press
to continue programming.
Note: The radio retains settings for channels made unavailable.
S
29
®
Programming Call Tones and VibraCall (CLS1410 only)
Your radio can transmit call tones to other radios in your group so you can alert them
that you are about to talk. Your radio is programmed at the factory with call tones
turned off (set to 0), but you can change this setting to choose a distinctive call tone.
®
The VibraCall feature is an additional call tone option that makes the CLS1410 radio
vibrate briefly when it receives if you have not transmitted or received in the last
®
30 seconds. Select call tone 4 to turn VibraCall on. idisplays on the radio when
®
VibraCall is on.
1. In programming mode, press S until Edisplays.
2. Press
or
to hear and select the call tone. Select call tone 4
[
]
®
for VibraCall (CLS1410 only).
3. Press and hold Push to Talk to exit programming mode, or press
to continue programming.
To transmit your call tone, press
S
on the side of the radio.
B
30
Programming Microphone Gain
You can adjust the microphone sensitivity to suit different users or operating
environments.
1. In programming mode, press
until g and ?display.
S
2. Press
or
to select the sensitivity level:
[
]
3= High sensitivity, for quiet environments
2= Medium sensitivity (default)
1= Low sensitivity, for loud environments
3. Press and hold Push to Talk to exit programming mode, or press
programming.
to continue
S
Editing the Scan List (CLS1410 Only)
For faster scanning and to avoid hearing unwanted transmissions, you can edit the
scan list to skip channels.
1. In programming mode, press S until h displays and the channel
number and Yor nflash.
2. Press [ or ] to select the channel you want to remove from the
scan list.
3. Press T to display either Yto include the channel or nto exclude
the channel.
4. Press and hold Push to Talk to exit programming mode, or press
to continue
S
programming.
31
Cloning Radio Settings
You can copy _Series radio settings from one radio (the source) to a second
radio using the 56531 Multi-Unit Charger (MUC) optional accessory. See the MUC
User's Guide for more information.
You can clone only one radio at a time. A multi-channel radio can clone to a single-
channel radio, but only the first channel is cloned. The MUC does not have to be
plugged in for cloning, but both radios require charged batteries.
1. On the source radio, press and hold Push to Talk and T for 3 seconds while
turning the radio on. The radio beeps and displays k.
2. Place the source radio in one of the charging pockets.
Paired
pockets
3. Turn the target radio on and place it in the charging pocket
that is paired with the pocket containing the source radio.
There are 3 paired charging pockets as indicated by the
3 pairs of charging status LEDs.
4. Press and hold T on the source radio. The source radio
transmits its settings to the target radio. If cloning was
successful, P or Pass or “F” for Fail displays on the source
radio and the target radio displays all feature icons. If cloning
was not successful, F or Fail displays on the source radio.
5. Turn the target radio off and back on again to use.
6. To clone another radio, repeat steps 3 and 4.
LEDs
7. To exit programming mode on the source radio, press and hold Push to Talk
until k no longer appears.
32
Advanced Features
You can set the following features by pressing and holding additional buttons while
turning the radio on.
Press This Button
Default
To Do This
Turn Keypad Tones On/Off
Turns keypad beeps off for silent keypad operation.
Turn End-of-Transmission Tone On/Off
While Turning
the Radio On
Setting
On
[
If enabled, your two-way radio transmits a tone
when you finish transmitting (like saying Roger or
Over).
If keypad tones are off and end-of-transmission tone
is on, you will not hear the end-of-transmission tone,
but it is transmitted.
Off
]
33
Press This Button
While Turning
the Radio On
Default
Setting
To Do This
Turn Battery Save Mode On/Off
Decreases attack time, which is the brief period of
time between when the radio receives a
transmission on its frequency and broadcasts audio.
Turning battery save mode off decreases battery life
by approximately 20%.
On
---
Push to Talk T [
Restore Factory Defaults
Returns radio to its original factory settings.
Push to Talk
S
34
Troubleshooting
Symptom
Try This:
Recharge or replace Li Ion battery.
Reposition or replace Alkaline batteries.
No Power
Make sure Push to Talk is completely pressed while
transmitting.
Recharge, replace, and/or reposition batteries.
Verify the transmit light is illuminated while speaking.
Verify Channel, Frequency, and Code settings are correct.
Message not
transmitted
Hearing other
noises or
conversation on
a channel
Frequency may be in use. Change on all radios if possible (see
page 28 and 29).
Bandwidth does not match. For optimal audio quality when
communicating with _Series radios, the bandwidth of other
radios should be set to 12.5 kHz, if possible.
Poor audio
quality
35
Symptom
Try This:
Steel and/or concrete structures, heavy foliage, buildings, or
vehicles decrease range (see page 22). Check for clear line of
sight to improve range.
Limited talk
range
Wearing radio close to body such as in a pocket or on a belt
decreases range. Change location of radio.
Confirm radios have the same channel, frequency, and
interference eliminator code settings (see page 26).
Recharge, replace, and/or reposition batteries.
Message not
received
Move to another location. Obstructions and operating indoors or
in vehicles may decrease range.
Verify radio is not in scan mode (CLS1410 only, see page 24).
Radios are too close. They must be at least 5 feet apart.
Heavy static or
interference
Radios are too far apart or obstacles are interfering with
transmission.
Keypad locked
Low batteries
Unlock by holding S for 3 seconds.
Recharge or replace batteries. Extreme operating temperatures
affect battery life.
36
Symptom
Try This:
Reinsert radio and/or battery.
Clean battery and/or charger contacts.
Charger light
does not come
on
Verify that the charging pin on the transformer is inserted
correctly into the drop-in charger.
AAA cells installed in radio. Remove and replace with Li Ion
battery.
Low battery
meter reading
although new
batteries are
installed
Verify radio is set to the correct battery type (see page 15).
Verify high-capacity alkaline batteries are used for optimal
battery life.
Feature not set and on (see page 22).
Sensitivity set to 0(see page 23).
Cannot activate
VOX (CLS1410
only)
Verify that accessory allows VOX operation.
Cannot enter
Unplug audio accessories and retry.
k
mode
37
Use and Care
Use a soft damp cloth
to clean the exterior.
Do not immerse
in water.
Do not use alcohol or
cleaning solutions.
If the radio is submerged in water...
Turn radio off and
remove batteries.
Do not use radio until
completely dry.
Dry with soft cloth.
38
Frequencies and Bandwidths
These charts provide frequency information and are useful when using Motorola
_ Series radios with other business radios. Frequency Display Number is
identical to Spirit M, GT, and S-Series frequency position (where applicable), but
bandwidth may be different.
UHF Frequencies
Display
Number
Frequency
(MHz)
Display
Number
Frequency
(MHz)
Bandwidth
Bandwidth
1
2
3
4
5
6
7
464.5000
464.5500
467.7625
467.8125
467.8500
467.8750
467.9000
12.5
12.5
12.5
12.5
12.5
12.5
12.5
8
467.9250
461.0375
461.0625
461.0875
461.1125
461.1375
461.1625
12.5
12.5
12.5
12.5
12.5
12.5
12.5
9
10
11
12
13
14
39
UHF Frequencies (Continued)
Display
Number
Frequency
Display
Number
Frequency
(MHz)
(MHz)
Bandwidth
Bandwidth
15
16
17
18
19
20
21
22
23
24
25
461.1875
461.2125
461.2375
461.2625
461.2875
461.3125
461.3375
461.3625
462.7625
462.7875
462.8125
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
26
27
28
29
30
31
32
33
34
35
36
462.8375
462.8625
462.8875
462.9125
464.4875
464.5125
464.5375
464.5625
466.0375
466.0625
466.0875
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
40
UHF Frequencies (Continued)
Display
Number
Frequency
Display
Number
Frequency
(MHz)
(MHz)
Bandwidth
Bandwidth
37
38
39
40
41
42
43
44
45
46
466.1125
466.1375
466.1625
466.1875
466.2125
466.2375
466.2625
466.2875
466.3125
466.3375
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
47
48
49
50
51
52
53
54
55
56
466.3625
467.7875
467.8375
467.8625
467.8875
467.9125
469.4875
469.5125
469.5375
469.5625
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
41
Interference Eliminator Codes
Display Code
Display Code
Display Code
Number
(Hz)
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
Number
14
(Hz)
Number
27
(Hz)
1
2
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
15
28
3
16
29
4
17
30
5
18
31
6
19
32
7
20
33
8
21
34
9
22
35
10
11
12
13
23
36
24
37
25
38
26
Carrier Squelch (0) disables interference eliminator codes.
42
Digital Interference Eliminator Codes
Display
Number
Digital
Code
Display
Number
Digital
Code
Display
Number
Digital
Code
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
023
025
026
031
032
043
047
051
054
065
071
072
073
074
114
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
115
116
125
131
132
134
143
152
155
156
162
165
172
174
205
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
223
226
243
244
245
251
261
263
265
271
306
311
315
331
343
43
Digital Interference Eliminator Codes (Continued)
Display
Number
Digital
Code
Display
Number
Digital
Code
Display
Number
Digital
Code
84
85
86
87
88
89
90
91
92
93
94
95
96
346
351
364
365
371
411
412
413
423
431
432
445
464
97
465
466
503
506
516
532
546
565
606
612
624
627
631
110
111
112
113
114
115
116
117
118
119
120
121
632
654
662
664
703
712
723
731
732
734
743
754
98
99
100
101
102
103
104
105
106
107
108
109
44
Spirit GT Series Programming
The _Series platform is designed to replace the Spirit GT Series radio. The first
eight frequencies and 38 interference eliminator codes of _Series are
compatible with Spirit GT Series. To program your _Series radio to talk with a
Spirit GT Series, verify or change your Spirit GT settings as follows.
To verify the frequency and code:
1. Press the Menu button 3 times. The channel number and frequency display.
2. Press Menu again. The interference eliminator code displays.
To change the frequency:
1. Enter programming mode by pressing and holding Push to Talk for
approximately 5 seconds while turning the radio on, then release Push to Talk
.
2. Use the Scroll button to select one the eight frequencies.
To change the interference eliminator code:
1. Enter programming mode by pressing and holding Push to Talk for
approximately 5 seconds while turning the radio on, then release Push to Talk
.
2. Press the Menu button. The code number flashes.
3. Use the Scroll button to select the code.
To exit programming mode on a Spirit GT Series radio, press Push to Talk or the
radio will exit programming mode after five seconds.
45
Limited Warranty for Motorola Personal Communications Products
Purchased in the United States and Canada
Warranty
I.
What This Warranty Covers
• Products. Defects in materials and workmanship in wireless cellular telephones, pagers,
and/or two-way radios, and certain accessories that are sold with them, such as the battery,
battery charger, and holster manufactured and/or sold by Motorola (Products).
• Batteries. Defects in materials and workmanship in batteries that are manufactured by
Motorola and/or sold with Products are covered by this warranty only if the fully-charged
capacity falls below 80% of rated capacity or they leak.
• Software. Physical defects in the media that tangibly embodies each copy of any software
supplied with the Products.
II. What the Period of Coverage Is
From the date the Products are purchased by the first end-user:
• Products. The warranty is for one year. Exception: The warranty for Spirit GT Series and
Talkabout Series two-way radio accessories (including the Spirit GT Series batteries) is for
90 days.
• Software. The warranty is for 90 days.
• Repairs/Replacements. The warranty is for the balance of the original warranty or for 90
days from the date you receive it, whichever is longer.
46
III. Who is Covered
This warranty extends to the first end-user purchaser only.
IV. What We Will Do to Correct Warranty Problems
At no charge to you, we have the option to repair or replace the Products or software that do not
conform to the warranty, or to refund the Products’ purchase price. We may use functionally
equivalent reconditioned/refurbished/pre-owned or new Products or parts. No software updates are
provided.
V. How to Obtain Warranty Service or Other Information
USA
Phones 1-800-331-6456
Pagers 1-800-548-9954
Two-Way Radios 1-800-448-6686
All Products 1-800-461-4575
TTY 1-888-390-6456
Canada
TTY
For Accessories and Software, please call the telephone number designated above for the
product with which they are used.
47
You will receive instructions on how to ship the Products to Motorola. You must ship the Products to
us with freight, duties and insurance prepaid. Along with the Products you must include: (a) a copy
of your receipt, bill of sale or other comparable proof of purchase; (b) a written description of the
problem; (c) the name of your service provider (if this Product requires subscription service); (d) the
name and location of the installation facility (if applicable) and, most importantly; (e) your address
and telephone number. If requested, you must also return all detachable parts such as antennas,
batteries and chargers. RETAIN YOUR ORIGINAL PROOF OF PURCHASE.
We will ship repaired or replacement Products at our expense for the freight and insurance, but at
your expense for any duties. If additional information is needed, please contact us at the telephone
number listed above.
VI. What This Warranty Does Not Cover
•
Products that are operated in combination with ancillary or peripheral equipment or software
not furnished by Motorola for use with the Products (“ancillary equipment”), or any damage
to the Products or ancillary equipment as a result of such use. Among other things,
“ancillary equipment” includes batteries, chargers, adaptors, and power supplies not
manufactured or supplied by Motorola. Any of these voids the warranty.
•
Someone other than Motorola (or its authorized service centers) tests, adjusts, installs,
maintains, alters, modifies, or services the Products in any way. Any of these voids the
warranty.
48
•
Rechargeable batteries that: (a) are charged by other than the Motorola-approved battery
charger specified for charging such batteries; (b) have any broken seals or show evidence
of tampering; (c) are used in equipment other than the Product for which they are specified;
or (d) are charged and stored at temperatures greater than 60 degrees centigrade. Any of
these voids the warranty.
•
•
Products that have: (a) serial numbers or date tags that have been removed, altered, or
obliterated; (b) board serial numbers that do not match each other, or board serial numbers
that do not match the housing; or (c) nonconforming or non-Motorola housings or parts. Any
of these voids the warranty.
Defects or damage that result from: (a) use of the Products in a manner that is not normal or
customary; (b) improper operation or misuse; (c) accident or neglect such as dropping the
Products onto hard surfaces; (d) contact with water, rain, extreme humidity, or heavy
perspiration; (e) contact with sand, dirt or the like; or (f) contact with extreme heat, or spills
of food or liquid.
•
•
Physical damage to the surface of the Products, including scratches, cracks, or other
damage to a display screen, lens, or other externally exposed parts.
Failure of Products that is due primarily to any communication service or signal you may
subscribe to or use with the Products.
•
•
Coil cords that are stretched or that have any broken modular tabs.
Products that are leased.
49
Flat-rate repair rates may apply to Products not covered by this warranty. To obtain information
about Products needing repairs that are not covered by this warranty, please call the telephone
number previously listed. We will provide information on repair availability, rates, methods of
payment, where to send the Products, etc.
VII. Some Other Limitations
This is Motorola’s complete warranty for the Products, and states your exclusive remedies.
This warranty is given in lieu of all other express warranties. Implied warranties, including
without limitation, the implied warranties of merchantability and fitness for a particular
purpose, are given only if specifically required by applicable law. Otherwise, they are
specifically excluded.
No warranty is made as to coverage, availability, or grade of service provided by the
Products, whether through a service provider or otherwise.
No warranty is made that the software will meet your requirements or will work in
combination with any hardware or applications software products provided by third parties,
that the operation of the software products will be uninterrupted or error free, or that all
defects in the software products will be corrected.
In no event shall Motorola be liable, whether in contract or tort (including negligence) for
damages in excess of the purchase price of the Product, or for any indirect, incidental,
special or consequential damages of any kind, or loss of revenue or profits, loss of
business, loss of information or data, or other financial loss arising out of or in connection
with the ability or inability to use the Products, to the full extent these damages may be
disclaimed by law.
50
VIII. Patent and Software Provisions
At Motorola’s expense, we will defend you, and pay costs and damages that may be finally awarded
against you, to the extent that a lawsuit is based on a claim that the Products directly infringe a
United States patent. Our obligation is conditioned on: (a) you notifying us promptly in writing when
you receive notice of the claim; (b) you giving us sole control of the defense of the suit and all
negotiations for its settlement or compromise; and (c) should the Products become, or in Motorola's
opinion be likely to become, the subject of a claim of infringement of a United States patent, you
permit us, at our option and expense, either to: procure for you the right to continue using the
Products; replace or modify them so that they become non-infringing; or grant you a credit for such
Products, as depreciated, and accept their return. The depreciation will be an equal amount per
year over the lifetime of the Products, as established by Motorola.
Motorola will have no liability to you with respect to any claim of patent infringement that is based
upon the combination of the Products or parts furnished under this limited warranty with ancillary
equipment, as defined in VI., above.
This is Motorola’s entire liability with respect to infringement of patents by the Products.
51
Laws in the United States and other countries preserve for Motorola and other third party software
providers certain exclusive rights for copyrighted software, such as the exclusive rights to
reproduce in copies and distribute copies of such software. The software may be copied into, used
in and redistributed with only those Products that are associated with such software. No other use,
including without limitation, disassembly or reverse engineering of such software or exercise of
exclusive rights in such software is permitted.
Some states and other jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or limitation on the length of an implied warranty, so the above limitations
or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from jurisdiction to jurisdiction.
52
_Series Programming Quick Reference
To enter programming mode, press and hold Push to Talk
and Qfor 3 seconds while turning the radio on. The radio
beeps and displays k, the channel number flashes, and the
frequency (indicated by l) and code (indicated by y)
display alternately.
Set the
Channel*
Press
[
or
]
.
Press
Press
S
until ldisplays.
or to change the
Set the
Frequency
[
]
frequency.
Set the
Press
S
until
y
Interference
Eliminator
Code
displays.Press [or
the code.
]
to change
Press
Press
S
until =displays.
or to select
Set
Available
Channels*
[
]
number of available channels.
* CLS1410 Only
_Series Programming Quick Reference
Press
Press
S
until Edisplay.s
or to select1, 2, or
Set a Call
Tone
[
]
3 for audible call tones, 4 for
VibraCall, or 0 for off (default).
Press
Press
S
until g and ?display.
or to select:
Set the
Microphone
Gain
[
]
1 Low sensitivity
2 Medium sensitivity
3 High sensitivity
Press
S
until hdisplays and the
channel number and Yor nflash.
channel, then prestsoTselect the
to select Y
Press
[
or
]
Edit the
Scan List*
(include channel) or n(exclude
channel).
motorola.com
|