RKF
Roadking®- All models 94’-07’
The RoadKing®Flip Fork Lock Cover Clock or Thermometer takes the
place of the factory installed fork lock plate. The RKF comes with
TOCS
Installs to any flat surface or Roadking®tank panel
The Tape on Billet (TOCS) Clock or Thermometer can be installed by
using the supplied industrial grade two sided adhesive wherever you
would like, or using the supplied 1/4” x 20 screw for bolt down
either a clock or thermometer, one extra rubber compression ring, two
screws, one clear plastic spacer, one battery replacement tool and
billet mount.
applications like the Roadking®tank panel.
The TOCS comes with either a clock or thermometer, one extra rubbe
compression ring, two adhesive pads, one 1/4”x 20 screw, one battery
replacement tool and billet mount.
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the long flat
side of a knife or similar object in a screwdriver style motion or use the “Pull Here” tab if so
equipped, you may also be able to push through the hole in the bottom of the holder. Make sure
that the clock does not fall and become damaged.
3) Carefully pry off factory plastic fork lock plate that has Unlock-Lock on it.
4) Then remove the two Phillips screws beneath the lock plate.
5) Open the mount by pulling the top half up from the base, place the mount and the clear
rubber spacer that goes under the mount in position over the two exposed screw holes.
6) Apply LOCTITE®242 blue to the thread of the screws provided and install the screws to hold
the cover in place. (The LOCTITE®prevents loosening of threaded fasteners.)
7) The Fork Lock Cover spring closes cover automatically. (The cover WILL NOT stay open)
8) After setting the time per instructions on bag, install the clock into the holder/mount all the
way as per instructions on in the General Care section of these instructions.
NO KEY MODIFICATION IS REQUIRED FOR RKF
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or
similar object in a screwdriver style motion or use the “Pull Here” tab if so equipped, you may
also be able to push through the hole in the bottom of the holder. Make sure that the clock does
not fall and become damaged.
3) To install on the center console / tank panel of your Road King®just remove the screw from
the center console washer and replace factory screw and washer assembly with the TOCS
mount holder, using the supplied screw.
3a) For double sided adhesive application make sure the area you are mounting to is clean and
free of debris and oils. A flat, smooth, clean surface is best suited for optimal holding strength.
4) After setting the time per instructions on bag, install the clock into the holder/mount all the
way as per instructions in the General Care section of these instructions.
RKS
Roadking®- All models 94’-07’
The Road King®Swivel Fork Lock Cover Clock or Thermometer
takes the place of the factory installed fork lock plate. The RKS
comes with either a clock or thermometer, one extra rubber
FLHT All “Glide” Models
The FLHTC/FLHTCI ELECTRA GLIDE®CLASSIC clock or
thermometer takes the place of the existing factory fairing plugs. The
FLHTC/FLHTCI ELECTRA GLIDE®CLASSIC clock or thermometer
comes with, one extra rubber compression ring, one battery
replacement tool and factory style fairing mount.
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the l
similar object in a screwdriver style motion or use the “Pull Here” tab if so equipped, you may
also be able to push through the hole in the bottom of the holder. Make sure that the clock does
not fall and become damaged.
3) The installation instructions of your fairing/windshield, from your owners manual or service
manual to will give you the information on removal and replacing the factory fairing plugs.
4) After setting the time per instructions on bag, install the clock into the holder/mount all the
way as per instructions in the General Care section of these instructions.
Installation tip from a valued customer:
“It took me longer to get my drill out to cut a hole in the plugs than it did to install the clock and
thermometer! I did not have to remove the fairing at all. I wish all things were that easy to install.
;-) Once I cut a 1/2" hole, put my finger in it and pulled, the factory plug came out and the new
parts just snapped right into place!”
compression ring, two screws, one clear plastic spacer, one battery
replacement tool and billet mount.
1) Carefully remove the item from it’s package.
2) To remove the clock pry slowly under the edge of the clock with the long
flat side of a knife or similar object in a screwdriver style motion or use the “Pull Here” tab if so
equipped, you may also be able to push through the hole in the bottom of the holder. Make sure
that the clock does not fall and become damaged.
3) Carefully pry off factory plastic fork lock plate that has Unlock-Lock on it.
4) Then remove the two Phillips screws beneath the lock plate.
5) Open the mount by rotating the top half clockwise, place the mount and the clear rubber
spacer that goes under the mount in position over the two exposed screw holes.
6) Apply LOCTITE®242 blue to the thread of the screws provided and install the screws to hold
the cover in place.
(The LOCTITE®prevents loosening of threaded fasteners.)
7) The Fork Lock Cover turns counterclockwise to close.
8) After setting the time per instructions on bag, install the clock into the holder/mount all the way
as per instructions in the General Care section of these instructions.
9) Your will need to modify your key. The blade of the key will hit the head of the clock mount. You
need to grind one edge of your key as shown in the photo. If you feel that you do not want cut
®
FSBC2
Fits FXDWG®, All 06’-07’ Dynas
And 91’-07’ Softails®(Except Springers)®
®
your original key, purchase a spare key from your Harley Davidson. Dealer. They come in pairs.
The FSBC2, Large Fork Stem Clock or Thermometer, takes the place
of the factory chrome fork stem bolt cap/cover.
The FSBC2 comes with clock or thermometer, one extra rubber
compression ring, one 1/4”x 20 screw , one battery replacement tool
and billet mount.
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or
similar object in a screwdriver style motion or use the “Pull Here” tab if so equipped, you may
also be able to push (the bolt) through the hole in the bottom of the holder. Make sure that the
clock does not fall and become damaged.
3) Carefully remove the factory chrome cap from over the fork stem bolt by holding firmly and
turning counterclockwise.
BBCS2
Most 7/8”-1”-1 1/4” Bars
The Bullet Billet Clock or Thermometer fits on 1" bars or 7/8“ bars
utilizing the included clear plastic spacer.
The Bullet Billet 1 1/4” Clock or Thermometer fits on 1 1/4" bars.
4) Place the FSBC2 mount in position over the exposed screw hole in the fork stem nut, insert
the supplied screw and tighten.
6) After setting the time per instructions on bag, install the clock into the holder/mount all the
way as per instructions in the General Care section of these instructions.
Please note how the unit is assembled so you can re-assemble it
properly on the bar.
The BBCS2 comes with either a clock or thermometer, one extra rubber
compression ring, two internal screws, one clear plastic spacer, one hex head wrench, one battery
replacement tool and billet mount.
®
®
FSBC1
Fits All Sportsters,® FXRS,®FXRS-SP, FXRS-CON
FXLR® and Later FXD®& Pre-06’ Dyna Glide ® Models.
The BBCS2 1 1/4” has an additional face plate including two additional screws.
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or
similar object in a screwdriver style motion or use the “Pull Here” tab if so equipped. Make sure
that the clock does not fall and become damaged.
The FSBC1 Small Fork Stem Clock or Thermometer, takes the place
of the factory chrome fork stem bolt cap/cover or covers the exposed
stem nut.The FSBC1 comes with clock or thermometer, one extra
rubber compression ring, one 1/4”x 20 screw , one battery replacement
tool and billet mount.
3) Remove the two internal screws, separating the two bullet halves.
3a) The BBCS2 1 1/4” requires the removal and re-installation of a face
plate via two additional screws that the clock will insert into.
4) Place the BBCS2 mount halves in the position of your choice on the bars (a flat area looks
best, keep away from curves or areas the bar may not be a consistent thickness), re-insert the
supplied screws and tighten gently and evenly (for the mount to tighten properly there should be a
small gap between the two halves, no bar is the same so the gap will vary - do not over-tighten ).
4a) The BBCS2 1 1/4” requires the removal and re-installation of a face
plate via two additional screws that the clock will insert into.
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or
similar object in a screwdriver style motion or use the “Pull Here” tab if so equipped, you may
also be able to push (the bolt) through the hole in the bottom of the holder. Make sure that the
clock does not fall and become damaged.
3) Carefully remove the factory chrome cap from over the fork stem bolt by holding firmly and
turning counterclockwise.
4) Place the FSBC1 mount in position over the exposed screw hole in the fork stem nut, insert
the supplied screw and tighten.
6) After setting the time per instructions on bag, install the clock into the holder/mount all the
way as per instructions in the General Care section of these instructions.
5) After setting the time per instructions on bag, install the clock into the holder/mount all the way
as per instructions in the General Care section of these instructions.
General Care, Installation and Operation Instructions
HBC
Most 7/8”-1”-1 1/4” Bars
The Handlebar Clock or Thermometer fits on 1" bars or 7/8“ bars
utilizing the included clear plastic spacer.
IMPORTANT - READ THIS FIRST!
DO NOT push on the glass face when inserting the clock or thermometer into the holder / mount.
Push on the chrome ring or bezel to insert. Make sure clock or thermometer is inserted all the way
into holder / mount before riding or loss and / or damage may result.
The Handlebar 1 1/4” Clock or Thermometer fits on 1 1/4" bars or 1“
bars utilizing the included clear plastic spacer.
Please note how the unit is assembled so you can re-assemble it
properly on the bar.
The Handlebar Mount comes with either a clock or thermometer, one extra rubber compression
ring, one clear plastic spacer, one hex head wrench, one battery replacement tool and billet
mount.
When the clock or thermometer has been installed in the holder/mount for a long time and you
remove it from the holder/mount to change the time or other reason, the rubber compression ring
may stay compressed. To avoid a loose fit put a fresh compression ring on the clock or
thermometer ( a spare should have been supplied with the purchase of your new Marlin’s item ).
Note the compression rings position before removing it, the wide part of the nub molded into the
ring should face up and to the out side of the clock or thermometer. To rejuvenate or expand the
used compression ring back to it’s original size, place it in very hot water for a minute or two, then
put the ring in cold water and it will bring it back to shape for the next time you need to switch
compression rings.
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or
similar object in a screwdriver style motion or use the “Pull Here” tab if so equipped. Make sure
that the clock does not fall and become damaged.
3) Remove the two rear screws, separating the two mount halves.
4) Place the handlebar mount halves in the position of your choice on the bars (keep away from
curves or areas the bar may not be a consistent thickness), re-insert the supplied screws and
tighten gently and evenly (for the mount to tighten properly there should be a small gap between
the two halves, no bar is the same so the gap will vary - do not over-tighten ).
5) Loosen the hex screw on the head unit, move it into position desired and tighten hex screw to
lock head in place.
It is recommended when you take the clock or thermometer out of the holder/mount to use some
isopropyl alcohol and clean the inside rim of the holder/mount were the clock or thermometer goes
to eliminate any dirt or oils that could reduce the gripping power of the compression ring.
*The holder/mount and bezel can be polished and cared for with a quality chrome polish.*
Your new clock or thermometer is waterproof, shock resistant and the numbers may glow in the
dark if so equipped. The face must be exposed to a light source before you ride to charge and
activate the glow in the dark feature.
SETTING THE TIME: The crown to adjust the time is located behind the rubber ring at the 3 o’clock
position. To set the time, carefully pull the crown out and turn it until the desired time is show. Push
crown back in to the normal position to restart clock.
6) After setting the time per instructions on bag, install the clock into the holder/mount all the way
as per instructions in the General Care section of these instructions.
BATTERY REPLACEMENT: CAUTION: DO NOT LIFT THE MOVEMENT OUT OF THE CASE
When the clock loses time or stops the battery is due for replacement. The battery is accessible
from the backside of the clock. Our clocks are manufactured with a screw on/off back cover. For
your convenience we have supplied a tool to easily remove and replace the back cover. If you did
not receive the tool for any reason just call or email us. The battery is retained in position by a tiny
metal plate. Move the plate sideways to remove battery. Be sure when replacing battery to use the
same number or equivalent button cell, with positive pole (+) facing outward. Make sure that it is
retained securely in position by the metal plate. Replace cover making sure the O ring is properly in
position and will form a satisfactory seal.
HBDM
Most 7/8”-1”-1 1/4” Bars
The Handlebar Dual Mount Clock andThermometer fits on 1" bars or
7/8“ bars utilizing the included clear plastic spacer.
The Handlebar Dual Mount 1 1/4” Clock and Thermometer fits on 1 1/4"
bars or 1“ bars utilizing the included clear plastic spacer.
Please note how the unit is assembled so you can re-assemble it
properly on the bar.
The Handlebar Dual Mount comes with both a clock and thermometer, two extra rubber
compression rings, one clear plastic spacer, one hex head wrench, one battery replacement tool
and billet mount.
TO RE-INSERT YOUR CLOCK OR THERMOMETER INTO THE HOLDER/MOUNT:
You can moisten a paper towel with Windex or similar product, then wipe it on the rubber ring
around the clock to help you slide the clock in to the holder. ( Allow the Windex or other product to
dry completely before riding. ) Turn the clock in the position you like and push it in place, stem
section first, push inward on the chrome edges or bezel of the unit, making sure that the rubber ring
is not stuck on the edge of the holder/mount, ( you may use your fingernail or similar object to make
sure the rubber ring is in place properly ) and there is no gap so that the unit is firmly in place.
1) Carefully remove the item from its package.
2) To remove the clock and thermometer pry slowly under the edge of the unit with the long flat
side of a knife or similar object in a screwdriver style motion or use the “Pull Here” tab if so
equipped. Make sure that the unit does not fall and become damaged.
3) Remove the two rear screws, separating the two mount halves.
4) Place the handlebar mount halves in the position of your choice on the bars (keep away from
curves or areas the bar may not be a consistent thickness), re-insert the supplied screws and
tighten gently and evenly (for the mount to tighten properly there should be a small gap between
the two halves, no bar is the same so the gap will vary - do not over-tighten ).
5) Loosen the hex screw on the head unit, move it into position desired and tighten hex screw to
lock head in place.
BCM
The Brake/Clutch Mount Clock or Thermometer fits onto your brake or
clutch control unit using the existing mounting bolt. It may also be affixed to
a windshield horizontally and then adjusted up or down for better viewing.
The Brake/ClutchMount comes with either a clock or thermometer, one
extra rubber compression ring, one hex head wrench, one battery
replacement tool and billet mount.
6) Important: Access to the cross bar screw may not be gained until the phillips screws are
loose. Loosen the phillips head screws inside each of the two round holders and the hex screw
on the cross bar unit, move it into position desired and tighten hex screw to lock cross bar in
place, then continue to re-tighten the phillips head screws inside each of the two round holders
7) After setting the time per instructions on bag, install the clock into the
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or similar
object in a screwdriver style motion or use the “Pull Here” tab if so equipped. Make sure that the clock
does not fall and become damaged.
3) For control unit installation remove one bolt from the top or bottom of the handlebar control clamp.
4) Place the mount in position and re-insert the bolt and tighten.
5) Loosen the hex screw on the head unit, move it into position desired and tighten hex screw to lock
head in place.
Allen
Screw
holder/mount all the way as per instructions in the General Care section of
these instructions.
Note: When you loosen the allen screw on the dual mount,you can move
the head left or right. The allen in front will allow you to turn the dual
mount cross bar as you see in the photo. After you get everything
adjusted, tighten the allen screws.
6) After setting the time per instructions on bag, install the clock into the holder/mount all the way as
per instructions in the General Care section of these instructions.
FSBC1
with adapter Metrics & Customs
BCDM
The FSBC1 Small Fork Stem Clock or Thermometer with adapter,
covers the exposed stem nut. The FSBC1 with adapter comes with
The Brake/Clutch Mount Clock and Thermometer fits onto your brake or
clutch control unit using the existing mounting bolt. It may also be affixed to a
windshield horizontally and adjusted up or down for better viewing.
clock or thermometer, one extra rubber compression ring, one adapter
assembly with two hex set screws ( two longer set screws are also
included for smaller stem nut cases ) and assembly screw, one battery
replacement tool and billet mount.
1) Carefully remove the item from its package.
The Brake/ClutchMount comes with both a clock and thermometer, two extra
rubber compression rings, one hex head wrench, one battery replacement
tool and billet mount.
1) Carefully remove the item from its package.
2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or
similar object in a screwdriver style motion or use the “Pull Here” tab if so equipped, you may
also be able to push (the bolt) through the hole in the bottom of the holder. Make sure that the
clock does not fall and become damaged.
3) Carefully remove the adapter from the FSBC1 by removing the hex screw under the clock.
*The allen wrench used for the adapter installation is American.
2) To remove the clock pry slowly under the edge of the clock with the long flat
side of a knife or similar object in a screwdriver style motion or use the “Pull Here” tab if so equipped.
Make sure that the clock does not fall and become damaged.
3) For control unit installation remove one bolt from the top or bottom of the handlebar control clamp.
4) Place the mount in position and re-insert the bolt and tighten.
5) Loosen the hex screw on the head unit, move it into position desired and tighten hex screw to lock head
in place.
4) Take the adapter and remove the 2 hex set screws from the side of the adapter. Apply some
blue Loctite on the set screws, this will act as an anti seize and also stop them from coming out.
5) Take the adapter and put it over the stem nut and re-insert and tighten the set screws.
( Two longer set screws are also included for smaller stem nut cases )
6) Take the FSBC1 and put it over the adapter and attach it via the supplied assembly screw.
7) After setting the time per instructions on bag, install the clock into the holder/mount all the
way as per instructions in the General Care section of these instructions.
6) Important: Access to the cross bar screw may not be gained until the phillips screws are loose. Loosen
the phillips head screws inside each of the two round holders and the hex screw on the cross bar unit,
move it into position desired and tighten hex screw to lock cross bar in place, then continue to re-tighten
the phillips head screws inside each of the two round holders
Allen
Screw
7) After setting the time per instructions on bag, install the clock into the
holder/mount all the way as per instructions in the General Care section of these
instructions.
Note: When you loosen the allen screw on the dual mount,you can move the head
left or right. The allen in front will allow you to turn the dual mount cross bar as you
see in the photo. After you get everything adjusted, tighten the allen screws.
our Technical support: 248-683-1536
y
oy
P
nj
’s
E
rd
ouct
i
a
rln
M
|